4066-S14-R datasheet(4/7 Pages) UTC

4 / 7 page

4066

CMOS IC

UNISONICTECHNOLOGIESCO.,LTD

4 of 7

www.unisonic.com.tw

QW-R502-009,C

AC ELECTRICAL CHARACTERISTICS (AC Parameters are guaranteed by DC correlated testing)

(Ta=25 ,

℃

tr=tf=20 ns and Vss=0V unless otherwise)

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX UNITS

VDD=5V

VDD=10V

Propagation Delay Time Signal

Input to Signal Output

TPHL, TPLH

Vc=VDD, CL=50pF, (Figure1)

RL=200k

VDD=15V

VDD=5V

125

VDD=10V

Propagation Delay Time

Control Input to Signal

Output High Impedance to

Logical Level

tPZH, tPLZ

RL=1.0kΩ, CL=50pF

(Figure 2, Figure3)

VDD=15V

Propagation Delay Time

Control Input to Signal

Output Logical Level to

High Impedance

Sine Wave Distortion

Frequency Response -Switch

“ON” (Frequency at-3dB)

tPHZ, tPLZ

RL=1.0kΩ, CL=50pF, (Figure 2, Figure3)

VDD=5V

VDD=10V

VDD=15V

Vc=VDD=5V, Vss= -5V

RL=10kΩ, VIS=5VP-P, f=1kHz, (Figure 4)

Vc=VDD=5V, Vss= -5V

RL=1kΩ, VIS=5Vp-p

20 Log10 VOS/VOS (1kHz)-dB

(Figure 4)

0.1

125

MHz

Feedthrough - Switch “OFF”

(Frequency at –50 dB)

Crosstalk Between Any Two

Switches(Frequency at-50dB)

Crosstalk; Control Input to

Signal Output

Maximum Control Input

VDD=5.0V, Vcc=Vss= -5.0V,

RL=1kΩ, VIS=5.0VP-P, 20Log10,

VOS/VIS= -50dB, (Figure 4)

VDD=VC(A)=5.0V; Vss=Vc (B)=5.0V,

RL=1kΩ, VIS(A)=5.0VP-P, 20Log10,

VOS(B)/VIS (A)= -50dB (Figure 5)

VDD=10V, RL=10kΩ, RIN=1.0kΩ

Vcc=10V Square Wave, CL=50pF

(Figure 6)

RL=1.0kΩ, CL=50pF, (Figure 7)

Vos (f) =1/2Vos (1.0kHz)

VDD=5.0V

VDD=10V

VDD=15V

1.25

0.9

150

6.0

8.0

8.5

MHz

mVp-p

MHz

Signal Input Capacitance

CIS

8.0

Signal Output Capacitance

COS

VDD=10V

8.0

Feedthrough Capacitance

CIOS

VC=0V

0.5

Control lnput Capacitance

CIN

5.0

7.5

Note 1: These devices should not be connected to circuits with the power ”ON”

Note 2: In all cases, these is approximately 5pF of probe and jig capacitance in the output; however, this capacitance

is included in CL wherever it is specified.

Note 3: VIS is the voltage at the in/out pin and VOS is the voltage at the out/in pin. Vc is the voltage at the control

input.

Note 4: Conditions for VIHC: (a) VIS=VDD, Ios=standard B series IOH. (b) VIS=0V, IOL=standard B series IOL

4066-S14-R 数据表(PDF) 4 Page - Unisonic Technologies

4066-S14-R 数据表(HTML) 4 Page - Unisonic Technologies

Html Pages

1 2 3 4 5 6 7

数据表下载

链接网址

4066-S14-R 数据表(PDF) 4 Page - Unisonic Technologies

4066-S14-R 数据表(HTML) 4 Page - Unisonic Technologies

Html Pages

1 2 3 4 5 6 7

数据表 下载

链接网址

数据表下载