USB5807C datasheet(13/56 Pages) MICROCHIP

13 / 56 page



2019 - 2021 Microchip Technology Inc.

DS00003182B-page 13

USB5807C

Port 3

Power Enable /

Overcurrent

Sense

PRT_CTL3

I/OD12

(PU)

Port 3 Power Enable / Overcurrent Sense.

When the downstream port is enabled, this pin is set as

an input with an internal pull-up resistor applied. The

internal pull-up enables power to the downstream port

while the pin monitors for an active low overcurrent signal

assertion from an external current monitor on USB port 3.

This pin will change to an output and be driven low when

the port is disabled by configuration or by the host con-

trol.

Port 2

Power Enable /

Overcurrent

Sense

PRT_CTL2

I/OD12

(PU)

Port 2 Power Enable / Overcurrent Sense.

When the downstream port is enabled, this pin is set as

an input with an internal pull-up resistor applied. The

internal pull-up enables power to the downstream port

while the pin monitors for an active low overcurrent signal

assertion from an external current monitor on USB port 2.

This pin will change to an output and be driven low when

the port is disabled by configuration or by the host con-

trol.

Port 1

Power Enable /

Overcurrent

Sense

PRT_CTL1

I/OD12

(PU)

Port 1 Power Enable / Overcurrent Sense.

When the downstream port is enabled, this pin is set as

an input with an internal pull-up resistor applied. The

internal pull-up enables power to the downstream port

while the pin monitors for an active low overcurrent signal

assertion from an external current monitor on USB port 1.

This pin will change to an output and be driven low when

the port is disabled by configuration or by the host con-

trol.

Gang Power

GANG_PWR

GANG_PWR becomes the port control (PRTCTL) pin for

all downstream ports when the hub is configured for

ganged port power control mode. All port power control-

lers should be controlled from this pin when the hub is

configured for ganged port power mode.

FlexConnect

Control

FLEX_CMD

FlexConnect control input.

When low, the hub will operate in its default state. Port 0

is the upstream port and port 1 is a downstream port.

When high, the hub will operate in its flexed state. Port 0

is a downstream port and port 1 is an upstream port.

FlexConnect

Indicator

FLEX_STATE

O12

FlexConnect indicator output. Reflects the current state

of FlexConnect.

0 = Hub is in default mode of operation

1 = Hub is in flexed mode of operation.

TABLE 3-4:

PORT CONTROL PIN DESCRIPTIONS (CONTINUED)

Name

Symbol

Buffer

Type

Description

USB5807C 数据表(PDF) 13 Page - Microchip Technology

USB5807C 数据表(HTML) 13 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表下载

链接网址

USB5807C 数据表(PDF) 13 Page - Microchip Technology

USB5807C 数据表(HTML) 13 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

数据表 下载

链接网址

数据表下载