WM8976 datasheet(73/108 Pages) WOLFSON

73 / 108 page

Pre-Production

WM8976

PP Rev 3.0 April 2006

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

2:0

GPIO1SEL

000

CSB/GPIO1 pin function select:

000= input (CSB/jack detection:

depending on MODE setting)

001= reserved

010=Temp ok

011=Amute active

100=PLL clk o/p

101=PLL lock

110=logic 0

111=logic 1

GPIO1POL

GPIO1 Polarity invert

0=Non inverted

1=Inverted

GPIO

Control

5:4

OPCLKDIV

PLL Output clock division ratio

00=divide by 1

01=divide by 2

10=divide by 3

11=divide by 4

Table 61 CSB/GPIO Control

Note: If MODE is set to 3 wire mode, CSB/GPIO1 shall be used as CSB input irrespective of the

GPIO1SEL[2:] bits.

Note that SLOWCLKEN must be enabled when using the Jack Detect function.

For further details of the Jack detect operation see the OUTPUT SWITCHING section.

OUTPUT SWITCHING (JACK DETECT)

When the device is operated using a 2-wire interface the CSB/GPIO1 pin can be used as a switch

control input to automatically disable one set of outputs and enable another the most common use

for this functionality is as jack detect circuitry. The L2/GPIO2 and R2/GPIO3 pins can also be used

for this purpose.

The GPIO pins have an internal de-bounce circuit when in this mode in order to prevent the output

enables from toggling multiple times due to input glitches. This de-bounce circuit is clocked from a

slow clock with period 2

21 x MCLK and is enabled by the SLOWCLKEN bit.

Notes:

The SLOWCLKEN bit must be enabled for the jack detect circuitry to operate.

The GPIOPOL bit is not relevant for jack detection, it is the signal detected at the pin which is

used

Switching on/off of the outputs is fully configurable by the user. Each output, OUT1, OUT2, OUT3

and OUT4 has 2 associated enables. OUT1_EN_0, OUT2_EN_0, OUT3_EN_0 and OUT4_EN_0

are the output enable signals which are used if the selected jack detection pin is at logic 0 (after de-

bounce). OUT1_EN_1, OUT2_EN_1, OUT3_EN_1 and OUT4_EN_1 are the output enable signals

which are used if the selected jack detection pin is at logic 1 (after de-bounce).

The jack detection enables operate as follows:

All OUT_EN signals have an AND function performed with their normal enable signals (in Table 49).

When an output is normally enabled as per Table 49 the selected jack detection enable (controlled

by selected jack detection pin polarity) is set 0; it will turn the output off. If the normal enable signal is

already OFF (0), the jack detection signal will have no effect due to the AND function.

During jack detection if the user desires an output to be un-changed whether the jack is in or not,

both the JD_EN settings i.e. JD_EN0 and JD_EN1, should be set to 0000.

WM8976 数据表(PDF) 73 Page - Wolfson Microelectronics plc

WM8976 数据表(HTML) 73 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载