L320DB12VC datasheet(33/57 Pages) AMD

33 / 57 page

December 14, 2005

Am29LV320D

DA TA SH EET

RY/BY#: Ready/Busy#

The RY/BY# is a dedicated, open-drain output pin

which indicates whether an Embedded Algorithm is in

progress or complete. The RY/BY# status is valid after

the rising edge of the final WE# pulse in the command

sequence. Since RY/BY# is an open-drain output, sev-

eral RY/BY# pins can be tied together in parallel with a

pull-up resistor to V

CC.

If the output is low (Busy), the device is actively eras-

ing or programming. (This includes programming in

the Erase Suspend mode.) If the output is high

(Ready), the device is in the read mode, the standby

mode, or in the erase-suspend-read mode. Table 15

on page 33 shows the outputs for RY/BY#.

DQ6: Toggle Bit I

Toggle Bit I on DQ6 indicates whether an Embedded

Program or Erase algorithm is in progress or com-

plete, or whether the device entered the Erase Sus-

pend mode. Toggle Bit I may be read at any address,

and is valid after the rising edge of the final WE# pulse

in the command sequence (prior to the program or

erase operation), and during the sector erase time-out.

During an Embedded Program or Erase algorithm op-

eration, successive read cycles to any address cause

DQ6 to toggle. The system may use either OE# or

CE# to control the read cycles. When the operation is

complete, DQ6 stops toggling.

After an erase command sequence is written, if all

sectors selected for erasing are protected, DQ6 tog-

gles for approximately 100 µs, then returns to reading

array data. If not all selected sectors are protected, the

Embedded Erase algorithm erases the unprotected

sectors, and ignores the selected sectors that are pro-

tected.

The system can use DQ6 and DQ2 together to deter-

mine whether a sector is actively erasing or is

erase-suspended. When the device is actively erasing

(that is, the Embedded Erase algorithm is in progress),

DQ6 toggles. When the device enters the Erase Sus-

pend mode, DQ6 stops toggling. However, the system

must also use DQ2 to determine which sectors are

erasing or erase-suspended. Alternatively, the system

can use DQ7 (see the subsection on “DQ7: Data#

Polling” on page 30).

If a program address falls within a protected sector,

DQ6 toggles for approximately 1 µs after the program

command sequence is written, then returns to reading

array data.

DQ6 also toggles during the erase-suspend-program

mode, and stops toggling once the Embedded Pro-

gram algorithm is complete.

Table 15 on page 33 shows the outputs for Toggle Bit I

on DQ6. Figure 7, on page 31 shows the toggle bit al-

gorithm. Figure 21, on page 45 in the “AC Characteris-

tics” section shows the toggle bit timing diagrams.

Figure 22, on page 45 shows the differences between

DQ2 and DQ6 in graphical form. See also the subsec-

tion on DQ2: Toggle Bit II.

Figure 7.

Toggle Bit Algorithm

DQ2: Toggle Bit II

The “Toggle Bit II” on DQ2, when used with DQ6, indi-

cates whether a particular sector is actively erasing

(that is, the Embedded Erase algorithm is in progress),

START

Yes

DQ5 = 1?

Yes

Toggle Bit

= Toggle?

Program/Erase

Operation Not

Complete, Write

Reset Command

Program/Erase

Operation Complete

Read DQ7–DQ0

Toggle Bit

= Toggle?

Read DQ7–DQ0

Twice

Read DQ7–DQ0

Note: The system should recheck the toggle bit even if DQ5

= “1” because the toggle bit may stop toggling as DQ5

changes to “1.” See the subsections on DQ6 and DQ2 for

more information.

L320DB12VC 数据表(PDF) 33 Page - Advanced Micro Devices

L320DB12VC 数据表(HTML) 33 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

数据表下载

链接网址

L320DB12VC 数据表(PDF) 33 Page - Advanced Micro Devices

L320DB12VC 数据表(HTML) 33 Page - Advanced Micro Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

数据表 下载

链接网址

数据表下载