AM29F160DB90EC datasheet(14/47 Pages) SPANSION

14 / 47 page

Am29F160D

Am29F160D_00_D6 November 2, 2006

D A TA SH EE T

Autoselect Mode

The autoselect mode provides manufacturer and de-

vice identification, and sector protection verification,

through identifier codes output on DQ7–DQ0. This

mode is primarily intended for programming equipment

to automatically match a device to be programmed with

its corresponding programming algorithm. However,

the autoselect codes can also be accessed in-system

through the command register.

When using programming equipment, the autoselect

mode requires VID (11.5 V to 12.5 V) on address pin

A9. Address pins A6, A1, and A0 must be as shown in

Autoselect Codes (High Voltage Method) table. In addi-

tion, when verifying sector protection, the sector ad-

dress must appear on the appropriate highest order

address bits. Refer to the corresponding Sector Ad-

dress Tables. The Command Definitions table shows

the remaining address bits that are don’t care. When all

necessary bits are set as required, the programming

equipment may then read the corresponding identifier

code on DQ7–DQ0.

To access the autoselect codes in-system, the host

system can issue the autoselect command via the

command register, as shown in the Command Defini-

tions table. This method does not require VID. See

Command Definitions‚ on page 18 for details on using

the autoselect mode.

Table 4.

Am29F160D Autoselect Codes (High Voltage Method)

L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.

Sector Protection/Unprotection

The hardware sector protection feature disables both

program and erase operations in any sector. The hard-

ware sector unprotection feature re-enables both pro-

gram and erase operations in previously protected

sectors.

The device is shipped with all sectors unprotected.

AMD offers the option of programming and protecting

sectors at its factory prior to shipping the device

through AMD’s ExpressFlash™ Service. Contact an

AMD representative for details.

It is possible to determine whether a sector is protected

or unprotected. See Autoselect Mode‚ on page 12 for

details.

Sector protection/unprotection can be implemented via

two methods.

The primary method requires VID on the RESET# pin

only, and can be implemented either in-system or via

programming equipment. Figure 2, on page 14 shows

the algorithms and Figure 20, on page 39 shows the

timing diagram. This method uses standard micropro-

cessor bus cycle timing. For sector unprotect, all unpro-

tected sectors must first be protected prior to the first

sector unprotect write cycle.

The alternate method intended only for programming

equipment requires VID on address pin A9 and OE#.

This method is compatible with programmer routines

written for earlier 5.0 volt-only AMD flash devices. De-

tails on this method are provided in a supplement, pub-

lication number 22289. Contact an AMD representative

to request a copy.

Description

Mode

CE#

OE#

WE#

A19

A12

A11

A10

DQ8

DQ15

DQ7

DQ0

Manufacturer ID: AMD

VID

01h

Device ID:

Am29F160D

(Top Boot Block)

Word

VID

22h

D2h

Byte

D2h

Device ID:

Am29F160D

(Bottom Boot Block)

Word

VID

22h

D8h

Byte

D8h

Sector Protection Verification

VID

01h (protected)

00h

(unprotected)

AM29F160DB90EC 数据表(PDF) 14 Page - SPANSION

AM29F160DB90EC 数据表(HTML) 14 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

数据表下载

链接网址

AM29F160DB90EC 数据表(PDF) 14 Page - SPANSION

AM29F160DB90EC 数据表(HTML) 14 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47

数据表 下载

链接网址

数据表下载