TP-SW8

TP-SW8 Spec Rev 11 15-Mar-22

Specifications Subject to Change Without Notice

Page 2

Specifications

System Ordering:

TP-SW8-D

8 Port 802.3af/at compliant PoE Switch (no power supply included

– requires 46-57V DC

power source)

TP-SW8-NC

8 Port 12V-57V passive PoE Switch (no power supply included)

For further information contact:

TP-SW8-D / -NC

Ethernet Standard

IEEE802.3/IEEE802.3u (10 base-T/100base-T)

POE Standard (Port 1-8)

TP-SW8-D IEEE802.3af/at

TP-SW8-NC Passive POE 12-57VDC

Ports

One data/PoE input and seven data/PoE outputs

automatic crossover and polarity

Transmission Speed

100 Mbps(100base-T),10 Mbps(10base-T)

Auto-negotiation

Switch Technology

Store and Forward

Protocol

CSMA/CD

Flow Control

IEEE802.3x(full-duplex), Back Pressure(half-duplex)

Data Transmission Rate

148800pps for 100base-T, 14880pps for 10base-T

Address Table

2K MAC, self-learning

Connections

Shielded RJ45

POE Port

Port 1-7, auto power management

Pin assignment: TX(1,2), RX(3,6), V+(4,5), V-(7,8)

Maximum POE Power

Port 1-8, 2A Per Port

– NC Version

Port 1-7(35W), 8 (70W)

– 802.3af/at Version

Wire Terminal or DIN Connector Input Max 10A

POE Protection

Over Temperature, Over Current, Over/Under Voltage

Data Surge Protection

IEC61000-4-2 (ESD) ±15kV (air), ±8kV (contact)

IEC61000-4-4 (EFT) 40A (5/50ns)

IEC61000-4-5

(Lightning) 20A (8/20μs)

LED’s

Link (Green On, Yellow On)

Activity (Green Blinking, Yellow Blinking )

PoE Input Detect-4 pair (Yellow On)

PoE Input Detect-2 pair (Yellow Blinking)

Power On (Green On)

Power On Alarm (Red On)

DC Power Input

46V to 57V,

12V to 57V(-NC Version)

Dual DC Inputs, Reverse Polarity Protected.

Self Consumption

<1.5 Watts

Operating Temperature

-40 to +85°C (-40 to 185°F)

Operating Humidity (RH)

5% - 90% (non condensing)

MTBF (Mean Time Between

Failure)

70,281 Hours

Storage Temperature

-55 to +105°C (-67 to +221°F)

Dimensions (LxWxH)

159 x 116 x 40mm (6.3 x 4.6 x 1.6”)

Weight

0.45kg (1lb)

Warranty

3 Years

LED

STATUS

DESCRIPTION

P1~P8

Link/Act

Green

A network device is detected at

100Mbps, but no communication

activity is detected.

Green

Blinking

This port is transmitting to, or

receiving packet from another

device at 100Mbps.

Yellow

A network device is detected at

10Mbps, but no communication

activity is detected.

Yellow

Blinking

This port is transmitting to, or

receiving packet from another

device at 10Mbps.

Off

No device is detected.

LED

STATUS

DESCRIPTION

P1~P7

PoE PSE

Yellow

A valid Powered Device(PD) is

detected and delivering power on

this port.

Off

No PD is detected on this port.

P8

PoE PD

Yellow

4 pairs power source received

Yellow

Blinking

2 pairs power source received

Off

No PoE power detected on this port

LED

STATUS

DESCRIPTION

Power

Green

LED ON if either power input (port 8

or wire terminal) has valid power

applied

Red

LED ON if the following condition

happened.

*Power input under voltage (Vin<

12V)

*Wire Terminal Power input over

voltage (Vin>58V)

*PoE over current (>2A)

Off

No power in DC input

Tyconsystems.com

LED STATUS INDICATORS

14641 S 800 W Ste A

Bluffdale, UT 84065

PH: 801-432-0003

FAX: 801-618-4220