| 数据搜索系统,热门电子元器件搜索 |
|
PI616MC-AS 数据表(PDF) 8 Page - AMI SEMICONDUCTOR |
|
|
|||||||||||||||||||||||||||||
PI616MC-AS 数据表(HTML) 8 Page - AMI SEMICONDUCTOR |
|
8 / 22 page ![]() This table is defines the symbols used in the timing diagram, Figure 3. Timing Diagram. It is for a single video section. However it applies to all eight video sections. Accordingly, the system- timing diagram is a composition of this timing diagram repeated eight times with all waveforms in parallel, so electrically the system produces pixels from all eight video section simultaneously. ITEM SYMBOL MIN. TYPICAL MAX. UNITS CLOCK CYCLE TIME (2) to 0.1666 0.200 10 m s CLOCK PULSE WIDTH (2) tw 0.100 ns CLOCK DUTY CYCLE (2) duty 25 50 75 % PROHIBIT CROSSING TIME OF START PULSE tprh 30 ns DATA SETUP TIME tds 30 ns DATA HOLD TIME tdh 25 ns SIGNAL DELAY TIME tdl 75 ns SIGNAL SAMPLE TIME tsmp(3) 125 ns SIGNAL FALL TIME tsigf 75 ns RECOMMEND SP GENERATION Tonoff (4) 1. Applies to whole chart. All of the symbol definitions in above table are used in Figure 3, TIMING DIAGRAM. For the complete system, there are only two clocks, CP, and start pulse, SP and there logic levels are compatible with CMOS 74HCXX series logic devices. 2. See the notes on clock periods (the inverse of FREQ) and their duty cycle under Table 5.1 notes 3 and 4. 3. See PI3039 DATA SHEET page 6, Table 6A, note 6. 4. Recommend method for SP generation because the shift register loads only on the falling edge. 8.0 MAXIMUM RATINGS TABLE 8.1 MAXIMUM RATINGS (Not to be used for continuous operation) ITEM SYMBOL SPECIFICATION NOTE DC SUPPLY VOLTAGE VDD 7 V INPUT VOLTAGE VIN 0 TO VDD+0.3 SP & CP AMBIENT TEMPERATURE (1) TA (PCB Surface) 0 TO 70OC (See note, below.) -10O to +75OC (See note, below.) Operational Storage AMBIENT HUMIDITY (1) HA 0 to 80% (See note) Non Condensing MAXIMUM OPERATING CASE TEMPERATURE (1) PCB Temperature 70OC (See note, below.) Note (1) All referenced parameters are conservative engineering estimate based on few of the prototype PCB. They are based on measurements of similar CIS modules and/or simple bench top tests using heat guns and freeze sprays. However these parameters will be re-measured during the pilot production using standard QA practices that is under the control of ISO 9000 regulations. TABLE 7.2 CLOCK TIMING CHARACTERISTICS, SEE FIGURE 3. TIMING DIAGRAM PAGE 8 OF 22 - PI616MC-AS, 12/20/02 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |