ST72321 datasheet(129/189 Pages) STMICROELECTRONICS

129 / 189 page

ST72321

129/189

10-BIT A/D CONVERTER (ADC) (Cont’d)

10.8.3 Functional Description

The conversion is monotonic, meaning that the re-

sult never decreases if the analog input does not

and never increases if the analog input does not.

If the input voltage (VAIN) is greater than VAREF

(high-level voltage reference) then the conversion

result is FFh in the ADCDRH register and 03h in

the ADCDRL register (without overflow indication).

If the input voltage (VAIN) is lower than VSSA (low-

level voltage reference) then the conversion result

in the ADCDRH and ADCDRL registers is 00 00h.

The A/D converter is linear and the digital result of

the conversion is stored in the ADCDRH and AD-

CDRL registers. The accuracy of the conversion is

described in the Electrical Characteristics Section.

RAIN is the maximum recommended impedance

for an analog input signal. If the impedance is too

high, this will result in a loss of accuracy due to

leakage and sampling not being completed in the

alloted time.

10.8.3.1 A/D Converter Configuration

The analog input ports must be configured as in-

put, no pull-up, no interrupt. Refer to the «I/O

ports» chapter. Using these pins as analog inputs

does not affect the ability of the port to be read as

a logic input.

In the ADCCSR register:

– Select the CS[3:0] bits to assign the analog

channel to convert.

10.8.3.2 Starting the Conversion

In the ADCCSR register:

– Set the ADON bit to enable the A/D converter

and to start the conversion. From this time on,

the ADC performs a continuous conversion of

the selected channel.

When a conversion is complete:

– The EOC bit is set by hardware.

– The result is in the ADCDR registers.

A read to the ADCDRH resets the EOC bit.

To read the 10 bits, perform the following steps:

1. Poll the EOC bit

2. Read the ADCDRL register

3. Read the ADCDRH register. This clears EOC

automatically.

Note: The data is not latched, so both the low and

the high data register must be read before the next

conversion is complete, so it is recommended to

disable interrupts while reading the conversion re-

sult.

To read only 8 bits, perform the following steps:

1. Poll the EOC bit

2. Read the ADCDRH register. This clears EOC

automatically.

10.8.3.3 Changing the conversion channel

The application can change channels during con-

version. When software modifies the CH[3:0] bits

in the ADCCSR register, the current conversion is

stopped, the EOC bit is cleared, and the A/D con-

verter starts converting the newly selected chan-

nel.

10.8.4 Low Power Modes

Note: The A/D converter may be disabled by re-

setting the ADON bit. This feature allows reduced

power consumption when no conversion is need-

ed and between single shot conversions.

10.8.5 Interrupts

None.

Mode

Description

WAIT

No effect on A/D Converter

HALT

A/D Converter disabled.

After wakeup from Halt mode, the A/D

Converter requires a stabilization time

tSTAB (see Electrical Characteristics)

before accurate conversions can be

performed.

ST72321 数据表(PDF) 129 Page - STMicroelectronics

ST72321 数据表(HTML) 129 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载