ST72321 datasheet(186/189 Pages) STMICROELECTRONICS

186 / 189 page

ST72321

186/189

duration is always correct assuming the applica-

tion is not doing anything between the idle and the

break. This can be ensured by temporarily disa-

bling interrupts.

The exact sequence is:

- Disable interrupts

- Reset and Set TE (IDLE request)

- Set and Reset SBK (Break Request)

- Re-enable interrupts

15.1.7 16-bit Timer PWM Mode

In PWM mode, the first PWM pulse is missed after

writing the value FFFCh in the OC1R register

(OC1HR, OC1LR). It leads to either full or no PWM

during a period, depending on the OLVL1 and

OLVL2 settings.

15.1.8 I2C Multimaster

In multimaster configurations, if the ST7 I2C re-

ceives a START condition from another I2C mas-

ter after the START bit is set in the I2CCR register

and before the START condition is generated by

the ST7 I2C, it may ignore the START condition

from the other I2C master. In this case, the ST7

master will receive a NACK from the other device.

On reception of the NACK, ST7 can send a re-start

and Slave address to re-initiate communication

15.1.9 Read-out protection with LVD

The LVD is not supported if Readout protection is

enabled.

15.2 ALL FLASH DEVICES

15.2.1 Internal RC Oscillator with LVD

The internal RC can only be used if LVD is ena-

bled.

15.3 LIMITATIONS SPECIFIC TO REV Q AND

REV S FLASH DEVICES

15.3.1 ADC Accuracy

The improved ADC accuracy specifications given

in Section 12.12.3 do not apply to Rev Q and Rev

S devices. Their accuracy remains as specified in

the previous datasheet revision and summarized

in the table below.

To identify these parts, check the internal sales

type on the box label or the trace code marking on

the package.

15.4

LIMITATIONS

SPECIFIC

ROM

DEVICES

15.4.1 LVD Operation

Depending on the operating conditions, especially

the VDD ramp up speed and ambient temperature,

in some cases the LVD may not start. When this

occurs, the MCU may operate outside the guaran-

teed functional area (see datasheet Figure 76)

without being forced into reset state.

In this case, proper use of the watchdog may

make it possible to recover through a watchdog re-

set and allow normal operations to resume.

Consequently, the LVD function is not guaranteed

in the current silicon revision. For complete securi-

ty, an external reset circuit must be added.

Symbol

Parameter

Typ

Max

Unit

|ET|

Total unadjusted

error

LSB

|EO|

Offset error

|EG|

Gain Error

0.5

4.5

|ED|

Differential linearity

error

1.5

4.5

|EL|

Integral linearity er-

ror

1.5

4.5

Rev

Internal Salestype Trace Code

Rev Q

72F321xxx$A2

72F321xxx$U2

813xxxQ

Rev S

72F321xxx$A8

72F321xxx$U8

813xxxS

Rev 9 (full

spec)

72F321xxx$A3

72F321xxx$U3

813xxx9

ST72321 数据表(PDF) 186 Page - STMicroelectronics

ST72321 数据表(HTML) 186 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载