E3Z

-@-IL@

4

Ratings and Specifications

IO-Link Model

* Values in parentheses indicate the minimum required distance between the Sensor and Reflector.

Sensing method

Through-beam

Retro-reflective

with MSR function

Diffuse-reflective

Narrow-beam Models

PNP

output

Pre-wired

E3Z-T81-IL

@

E3Z-R81-IL

@

E3Z-D82-IL

@

E3Z-L81-IL

@

Model

Pre-wired

connector (M12)

E3Z-T81-M1TJ-IL

@

E3Z-R81-M1TJ-IL

@

E3Z-D82-M1TJ-IL

@

E3Z-L81-M1TJ-IL

@

Item

Connector (M8)

E3Z-T86-IL

@

E3Z-R86-IL

@

E3Z-D87-IL

@

E3Z-L86-IL

@

Sensing distance

15 m

4 m (100 mm) *

(when using E39-R1S)

3 m (100 mm) *

(when using E39-R1)

1 m

(white paper: 300

×

300 mm)

90 + 30 mm

(white paper: 100

×

100 mm)

Spot diameter (reference value)

---

2.5 dia. and sensing dis-

tance of 90 mm

Standard sensing object

Opaque: 12-mm dia. min. Opaque: 75-mm dia. min.

---

Minimum detectable object

(reference value)

---

0.1 mm (copper wire)

Differential travel

(representative example)

---

---

20% max. of setting distance Refer to

Engineering

data

on page

6

Directional angle

Both emitter and

receiver: 3 to 15

°

2 to 10

°

---

Light source (wavelength)

Infrared LED (870 nm)

Red LED (660 nm)

Infrared LED (860 nm)

Red LED (650 nm)

Power supply voltage

10 to 30 VDC (including 10% ripple (p-p))

Current consumption

50 mA max. (Emitter:

25 mA max., Receiver:

25 mA max.)

30 mA max.

Control output

Load power supply voltage: 30 VDC max., Load current: 100 mA max.

Residual voltage: Load current of less than 10 mA: 1 V max.

Load current of 10 to 100 mA: 2 V max.

PNP open collector output

Light-ON/Dark-ON selectable

Indicators

In the Standard I/O mode (SIO mode): Operation indicator (orange, lit) and stability indicator (green, lit)

In the IO-Link Mode: Operation indicator (orange, lit) and communication indicator (green, blinking at 1 s intervals)

Protection circuits

Reversed power supply

polarity protection, out-

put short-circuit protec-

tion, and reversed output

polarity protection

Reversed power supply polarity protection, output short-circuit protection,

reversed output polarity protection, and mutual interference prevention

Response time

Operate or reset: 1 ms max.

Sensitivity adjustment

Sensitivity adjuster / IO-Link communications

Ambient illumination

(Receiver side)

Incandescent lamp: 3,000 lx max.

Sunlight: 10,000 lx max.

Ambient temperature range

Operating:

−25 to 55°C (with no icing or condensation)

Storage:

−40 to 70°C (with no icing or condensation)

Ambient humidity range

Operating: 35% to 85%, Storage: 35% to 95% (with no condensation)

Insulation resistance

20 M

Ω min. at 500 VDC

Dielectric strength

1,000 VAC, 50/60 Hz for 1 min

Vibration resistance

Destruction: 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions

Shock resistance

Destruction: 500 m/s2 3 times each in X, Y, and Z directions

Degree of protection

IEC 60529 IP67

Connection method

Pre-wired cable (standard cable length 2 m), M12 pre-wired connector (standard cable length 0.3 m),

M8 connector

Weight

(packed

state)

Pre-wired cable (2 m)

Approx. 120 g

Approx. 65 g

Pre-wired connector (M12)

Approx. 60 g

Approx. 30 g

Connector (M8)

Approx. 30 g

Approx. 20 g

Material

Case

Polybutylene terephthalate (PBT)

Display

Modified polyarylate

Lens

Modified polyarylate

Methacrylate resin (PMMA) Modified polyarylate

Main IO-Link functions

Operation mode switching between Light ON and Dark ON, setup of the instability detection level for light

receiving and non-light receiving, timer function of the control output and timer time selecting, instability

output (IO-Link mode) ON delay timer time selecting, setup of a teaching level and execution of teaching,

setup of light receiving sensitivity level, monitor output, operating hours read-out, and initial reset

Communication

specifications

IO-Link

specification

Ver 1.1

Baud rate

-IL3: COM3 (230.4 kbps), -IL2: COM2 (38.4 kbps)

Data length

PD size: 2 bytes, OD size: 1 byte (M-sequence type: TYPE_2_2)

Minimum cycle

time

-IL3 (COM3): 1 ms, -IL2 (COM2): 2.3 ms

Accessories

Instruction manual (Neither Reflectors nor Mounting Brackets are provided with any of the above models.)