Page 4

Copyright © 2024 Sensata Technologies, Inc.

www.sensata.com

CONNECTIONS

14 Bit

GRAY or

NATURAL

BINARY

code

B13

(msb)

B12

B11

B10

B9

B8

B7

B6

B5

B4

B3

B2

B1

B0 (lsb)

DIR

(opt:

LATCH or

ENABLE)

CASE

GROUND

0V

LATCH

(opt:

DIR or

ENABLE)

+V

SHIELD

DRAIN

13 Bit

B12

(msb)

B11

B10

B9

B8

B7

B6

B5

B4

B3

B2

B1

B0

(lsb)

0V (opt:

ENABLE,

DIR or

LATCH)

12 Bit

std

B1

1(msb)

B10

B9

B8

B7

B6

B5

B4

B3

B2

B1

B0

(lsb)

n.c.

M14/19

M14 - 19

pins

A

B

C

D

E

F

G

H

J

K

L

M

N

P

R

S

T

U

V

-

Cable

Color

PVC cable

20 wires

WH/BK

WH/

BN

WH/

RD

WH/

OG

WH/

YE

WH/

GN

WH/

BU

WH/

VT

WH/

GY

WH

GY/

BK

GY/

BN

GY/

RD

GY/OG*

OG*

GN

BK

YE*

RD

BARE

Cable

Color

PVC cable

16 wires

GR

YE

GY

PK

BU

RD

BK

VT

WH/

BN

WH/

GR

WH/

YE

WH/

GY

-

-

WH/BU

Shield

WH

WH/PK

BN

-

A1 A2 A3 A4 A5

A+ OUT

A

RETURN

DIR

RESET *

0V

+V

CASE

GROUND

M18

M18

Connector

10 Pins

A

H

C

B

F

D

G

M14/19

M14

Connector

19 Pins

A

B

U

C

T

V

S

CABLE

COLOR

PVC Cable

9 Wires

YE

WH/YE

OG

BU

BK

RD

GN

A1 A2 A3 A4 A5

DATA +

DATA -

CLK +

CLK -

DIR

ENABLE*

0V

+V

CASE

GROUND

SHIELD

DRAIN

M18

M18

Connector

10 Pins

A

H

B

I

C

J

F

D

G

__

M14/19

M14

Connector

19 Pins

A

B

C

D

R

P

T

V

S

__

CABLE

COLOR

PVC Cable

9 Wires

YE

WH/YE

BU

WH/BU

OG

WH/OG

BK

RD

GN

BARE

ANALOG Connections

PARALLEL Connections

SSI Connections

* Optional

* Optional

* Optional

Functions

DIR: Standard is CW increasing when viewed from the shaft end, with pin DIR normally HI (pulled up internally to +V, or N/C).

To reverse the count direction, pin DIR must be pulled LO (0V COMMON).

RESET: Pin Reset is normally LO (pulled DOWN internally to +V, or N/C).

Encoder position code is reset to 0° for digital parallel /SSI outputs and to 180° for analog outputs if pin DIR is HI (to +V) for minimum 250ms.

LATCH: Encoder outputs are active and provide continuous parallel position information when Pin LATCH is HI (pulled up internally to +V, or N/C).

When pin LATCH is LO (0V COMMON) the encoder outputs are latched at the logic state that is present when the latch is applied and will stay latched until pin LATCH is no longer LO (0V

COMMON).

Er outputs are active and provide continuous parallel position information when pin ENABLE is HI (pulled up internally to +V, or N/C).

When pin ENABLE is LO (0V COMMON) the encoder outputs are switched off (tristated in high impedance) and will stay switched off until pin ENABLE is no longer LO (0V COMMON).

M18 Connector is a MS3102R18-1P, 10-pin connector on the encoder body and mates to an MS3106F18-1S connector or can be used with a standard cable/connector assembly, BEI P/N

924-31186-18XX (Where XX = 10, 20 30 or 50 for a 10, 20, 30, or 50 foot length). This is the preferred connector for SSI output.

M14/19 Connector is a MS3112E14-19P, 19-pin connector on the encoder body and mates to an MS3116J14-19S or equivalent.