H-79

(A)

Photo

electric

sensor

(B)

Fiber

optic

sensor

(C)

Door/Area

sensor

(D)

Proximity

sensor

(E)

Pressure

sensor

(F)

Rotary

encoder

(G)

Connector/

Socket

(H)

Temp.

controller

(I)

SSR/

Power

controller

(J)

Counter

(K)

Timer

(L)

Panel

meter

(M)

Tacho/

Speed/ Pulse

meter

(N)

Display

unit

(O)

Sensor

controller

(P)

Switching

mode power

supply

(Q)

Stepper

motor&

Driver&Controller

(R)

Graphic/

Logic

panel

(S)

Field

network

device

(T)

Software

(U)

Other

Dual PID Auto Tuning Control

Parameter 2 group

Parameter

Factory default Parameter

Factory default Parameter

Factory default Parameter

Factory default

IN-T

KCaH

AL-T

AL-A

PIDT

PIdS

H-SC

1300

EU-1

AL-1

AtT

TVN1

O-FT

HEAT

L-SC

-100

EU-2

AL-2

RAMP

OFF

UNIT

?C

LOC

OFF

※Press

( ) key and the right digit of SV display part flashes. Press

( ) or

( ) key and move to the desired digit.

Press

( ),

( ) keys to change SV and press MD key to complete the set. Press MD key again and it moves to next parameter.

※After completing setting at each parameter, press MD key for 3 sec. and it returns to RUN mode.

※If no key touched for 60sec., it will return to RUN mode automatically.

※1: It may not be displayed by input type switch.

※2: This is displayed only for model with High/Low-limit of transmission output.

Factory defaults(Parameter 2 group)

IN-T Input type: Select from 19 type

L-SC Set scaling low limit (include analog output)

EU-1 Event 1: Select from 9 type

DOT Select decimal point position for Analog input

EU-2 Event 2: Select from 9 type

FS-H Set the high-limit when retransmission output is applied. (20mA)

AL-T Alarm type: Select from 4 type

FS-L Set the low-limit when retransmission output is applied. (4mA)

AtT Auto-tuning: Selectable TUN1 or TUN2.

RAMP Able to set ON and OFF of Ramp function.

PIDT PID: Selectable PIDF or PIDS.

BPS Set communication speed

O-FT Selectable heat-function or cool-function

ADRS Set communication address(01 to 99)

UNIT Temperature unit:

℃ or ℉

LOC The data cannot be changed when the lock key is ON

H-SC Set scaling high limit (include analog output)

If pressing MD +

key for 3sec. at once in RUN state, it will go to parameter 2 group.

Input type

Event 1

mode

Alarm type

PID type

Control

operating

type

Temperature

unit

※2

※2

Input type

Lock

※2

Event 2

mode

Auto-tuning

type

Scaling

high limit

Transmission

output

low limit

Communication

address

Communication

speed

Ramp

function

Transmission

output

high limit

Scaling

low limit

※1

Decimal

point

※1

IN-T

KCaH

JIcH

JIcL

R PR

ECrL

ECrH

TCcH

TCcL

S PR

NN

U TT

JPtH

KCaL

JPtL

DPtH

DPtL

A--1

A--2

A--3

EU-1

LBA

SBA

AL-0

AL-1

AL-2

AL-4

AL-3

AL-5

AL-6

EU-2

LBA

SBA

AL-0

AL-1

AL-2

AL-4

AL-3

AL-5

AL-6

AL-T

AL-A

AL-B

AL-C

AL-D

IN-T

AtT

TVN1

TVN2

LOC

OFF

ON

PIDT

PIdS

PIdF

ADRS

01

O-FT

HEAT

COOL

BPS

2400

4800

9600

UNIT

?C

?F

H-SC

1300

RAMP

OFF

ON

L-SC

-100

FS-L

-100

FS-H

1300

DOT

0

)0

)00

)000

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

MD

Run mode

MD

+ 3sec.