STM32MP151AAB3T datasheet(123/245 Pages) STMICROELECTRONICS

123 / 245 page

DS12500 Rev 1

123/245

STM32MP151A

Electrical characteristics

228

1. All main power (VDD, VDDA, VDD33USB, VBAT) and ground (VSS, VSSA) pins must always be connected to

the external power supply, in the permitted range.

2. VIN maximum must always be respected. Refer to Table 47 for the maximum allowed injected current

values.

3. This formula has to be applied on power supplies related to the IO structure described by the pin definition

table.

4. To sustain a voltage higher than 4 V the internal pull-up/pull-down resistors must be disabled.

Table 11. Current characteristics

Symbols

Ratings

Max

Unit

ΣIVDD

Total current into sum of all VDD power lines (source)(1)

1. All main power (VDD, VDDA, VDD33USB) and ground (VSS, VSSA) pins must always be connected to the

external power supplies, in the permitted range.

TBD

ΣIVSS

Total current out of sum of all VSS ground lines (sink)(1)

TBD

IVDD

Maximum current into each VDD power pin (source)(1)

100

IVSS

Maximum current out of each VSS ground pin (sink)(1)

100

IIO

Output current sunk by any I/O and control pin

ΣI(PIN)

Total output current sunk by sum of all I/Os and control pins(2)

2. This current consumption must be correctly distributed over all I/Os and control pins. The total output

current must not be sunk/sourced between two consecutive power supply pins referring to high pin count

QFP packages.

140

Total output current sourced by sum of all I/Os and control pins(2)

140

IINJ(PIN)(3)(4)

3. Positive injection is not possible on these I/Os and does not occur for input voltages lower than the

specified maximum value.

4. A positive injection is induced by VIN>VDD while a negative injection is induced by VIN<VSS. IINJ(PIN) must

never be exceeded. Refer also to Table 10: Voltage characteristics for the maximum allowed input voltage

values.

Injected current on FT_xxx, TT_xx, RST and B pins except PA4,

PA5

-5/+0

Injected current on PA4, PA5

-0/0

ΣIINJ(PIN)

Total injected current (sum of all I/Os and control pins)(5)

5. When several inputs are submitted to a current injection, the maximum ∑IINJ(PIN) is the absolute sum of the

positive and negative injected currents (instantaneous values).

±25

Table 12. Thermal characteristics

Symbol

Ratings

Value

Unit

TSTG

Storage temperature range

-65 to +150

°C

Maximum junction temperature

125

STM32MP151AAB3T 数据表(PDF) 123 Page - STMicroelectronics

STM32MP151AAB3T 数据表(HTML) 123 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载