L9680 datasheet(39/286 Pages) STMICROELECTRONICS

39 / 286 page

DS11615 Rev 7

39/286

L9680

Start-up and power control

285

Figure 11. IC operating state diagram

6.3

ERBOOST switching regulator

The L9680 IC uses an advanced energy reserve switching regulator operating at 1.882MHz

nominal. The higher switching frequency enables the user to select smaller less expensive

inductors and moves the operating frequency to permit easier compliance with system

emissions.

The ERBoost switching regulator uses a classical peak current mode control loop to

properly regulate the output voltage and includes an over-voltage protection that

immediately switches off the PowerMOS to protect the device. The regulator includes also a

soft start circuit which applies a ramp on the over current threshold from the 40% of

IOC_ERBST value to the maximum one with 16 steps and within 1024 µs. The soft start is

restarted every time the regulator has a transition from the ER_BST_OFF to the

ER_BST_ON state.

The energy reserve boost regulator charges the external system tank capacitor through an

integrated fixed current source significantly reducing in-rush currents typical of large energy

reserve capacitors. The boost circuit provides energy for the reserve capacitor with

assumed run time load of less than 20 mA and to the VSF regulator. Once system shutdown

is initiated or a loss of battery condition is diagnosed, the boost regulator is by default

disabled so that system power can be taken from the energy reserve capacitor.

Alternatively, the ER Boost could be kept on even during the ER State by setting the

SYS_CFG(KEEP_ER_BOOST_ON) bit.

The energy reserve boost regulator defaults to 23 V at power-on and can be set to 33 V

nominal by the user through an SPI command. The boost converter can also be disabled by

the user through an SPI command. Enabling, disabling and setting the boost output voltage

GAPGPS02256

By safing engine

ARMx, VSF determined

(WD2_OVERRIDE OR WD2_RUN)

(WD1_OVERRIDE OR WD1_RUN) &

State

Diag

SSM Reset

SPI SAFING_STATE

State

Safing

State

Init

-W

-HS/LS GPO

-ARM in/out select

-PSINH

^SCRAPKEY state

ACLBAD=2 OR

SPI SCRAP_STATE

State

Arming

State

Scrap

VSF = 0

ARMx = 0

VSF = 1

ARMx = 1

atchdog timing thresholds

nfiguration enabled for:

SCRAPKEY state

ACLGOOD=3 AND

-PSI5/WSS select

-HS/LS GPO

-Deploy mask

-Safing Records and control

-Configuration anabled for:

-WSS

-HS/LS $ HSS FET

-Deploy time

-ARMx, VSF. PSINH

Testing enabled for:

L9680 数据表(PDF) 39 Page - STMicroelectronics

L9680 数据表(HTML) 39 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

L9680 数据表(PDF) 39 Page - STMicroelectronics

L9680 数据表(HTML) 39 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载