Copyright © 2008-2013 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, the Cree logo and XLamp® are registered

trademarks of Cree, Inc.

16

xlAMP xP-c lEDS

taPe and reel

All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard.

All dimensions in mm.

Loaded Pockets

(1,000 Lamps)

Leader

400mm (min) of

empty pockets with

at least 100mm

sealed by tape

(50 empty pockets min.)

Trailer

160mm (min) of

empty pockets

sealed with tape

(20 pockets min.)

START

END

Cathode Side

Anode Side

(denoted by + and circle)

160.0

A

A

B

2.5±.1

SECTION A-A

SCALE 2 : 1

1.5±.1

8.0±.1

4.0±.1

1.75±.10

12.0 .0

+.3

DETAIL B

SCALE 2 : 1

13mm

7"

Cover Tape

Pocket Tape

User Feed Direction

User Feed Direction

SIZE

TITLE

OF

REV.

SHEET

C

DRAWING NO.

DATE

DATE

DATE

CHECK

FINAL PROTECTIVE FINISH

MATERIAL

APPROVED

DRAWN BY

THIRD ANGLE PROJECTION

SCALE

A

B

C

D

1

2

3

4

5

6

6

5

4

3

2

1

A

B

C

D

Phone (919) 313-5300

Fax (919) 313-5558

4600 Silicon Drive

Durham, N.C 27703

UNAUTHORIZED PERSON WITHOUTTHE WRITTEN CONSENT

MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY

CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT

CONTAINED WITHIN ARE THE PROPRIETARY AND

CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION

OF CREE INC.

NOTICE

X°

±

.5 °

.XXX ±

.25

.XX ±

.75

.X

±

1.5

FOR SHEET METAL PARTS ONLY

.XX ±

.25

.XXX ±

.125

X°

±

.5 °

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN

MILLIMETERS AND AFTER FINISH.

TOLERANCE UNLESS SPECIFIED:

SURFACE FINISH: 1.6

B

B

+.10/-00

1.50

2.10 +.10/-.00

3.75 +.10/-.00

4.39 +.10/-.00

8.7°

8.00 ±.10

4.00 ±.10

2.00 ±.10

+.10/-.00

1.50

+.10/-.00

1.50

.30 ± .10

3.75 +.10/-.00

4.39 +.10/.00

12.00 Nominal

12.30 Max

5.50 ±.10

1.75 ±.10

10.25 ±.10

REVISONS

REV

DESCRIPTION

BY

DATE

APP'D

A

Released

J.L.

6/30/09

C

Match supplier drawing

DDS 10/21/10 Y.Gan

D

Zone A6, 2.15 was 2.1, tolerance was ±

.10 .

Zone C2, Added pocket dimensions.

DDS

12/2/10 Y.Gan

E

Zone A6, 2.10 was 2.15

DDS

1/3/11

J.M.

F

Zone B5, Added tolerance

to 4.39 and 3.75.

DDS

8/26/11

J.M.

G

ADDED CATHODE AND ANODE NOTE

DC 2/27/12

1

/

1

4.000

G

2402-00003

Carrier Tape, XPE

6/30/09

D. Seibel

Notes:

1. 10 sprocket hole pitch cumulative tolerance ±

0.2mm

CATHODE SIDE

ANODE SIDE

B-B

SECTION