数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

L6660 数据表(PDF) 7 Page - STMicroelectronics

部件名 L6660
功能描述  MILLI-ACTUATOR DRIVER
PDF  9 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

L6660 数据表(HTML) 7 Page - STMicroelectronics

  L6660 Datasheet HTML 1Page - STMicroelectronics L6660 Datasheet HTML 2Page - STMicroelectronics L6660 Datasheet HTML 3Page - STMicroelectronics L6660 Datasheet HTML 4Page - STMicroelectronics L6660 Datasheet HTML 5Page - STMicroelectronics L6660 Datasheet HTML 6Page - STMicroelectronics L6660 Datasheet HTML 7Page - STMicroelectronics L6660 Datasheet HTML 8Page - STMicroelectronics L6660 Datasheet HTML 9Page - STMicroelectronics  
Zoom Inzoom in Zoom Outzoom out
 7 / 9 page
background image
Not selected Output return to 0V
Using the Multiplexer features and selecting just
one driver, the second one, leaves its output volt-
age and "goes" to 0V (have showed in Fig. 3), in
"long time" with controlled slope see table 1.
Voltage reference
An internal 2.5V voltage reference generator is
connected to PIN13 (VrefOUT); it is based on an
internal Band-Gap reference with a total precision
of
±4% and a current capability of ±1.0mA, it is al-
ways present even in sleep mode condition.
This voltage is used to supply the internal MUX
logic, allowing both 3.3V or 5V logic input signals,
also the internal bias current is based on this ref-
erence.
The DC-DC converter reference voltage comes
from PIN14 (VrefIN), so that the user can use an
external voltage reference (from 2.0V up to 2.6V)
or the internal one, in this case, just shorting to-
gether VrefOUT and VrefIN (PIN13 and PIN14).
Voltage Shifter
A voltage shifter is inserted to allow a ground
symmetrical driving voltage on the piezo, starting
from a positive (0V up to 5V) input signal coming
from a positive supplied DAC. The DC Input-Out-
put typical tranfer function is plotted in Fig. 4. This
block works only in Double Supply mode, obvi-
ously it doesn’t work if no negative supply is pre-
sent. The voltage shifter output has not DC-cur-
rent capability.
For more details see the application note.
DC-DC CONVERTER DESCRIPTION
The DC-DC converter inside the chip can be sup-
plied from 5V up to 12V and has two parts, one to
supply the positive and one to supply the nega-
tive voltage.
The DC-DC converter loop "measures" the HVP
voltage by the EXTERNAL voltage divider and
PIN21. The HVP voltage is programmed by two
external resistors as shown in the block diagram,
its value is:
VHVP
= VPIN21 ⋅ (1 +
Rfdb1
Rfdb2
)
The DC-DC control loop precision will be im-
proved lower than
±4% respect external refer-
ence voltage and resistor voltage divider.
In Sleep Mode HVM is shorted to GND. When in
single supply, HVM must be connected to GND.
The topology is a standard resonant full-wave
boost one: the LC oscillation is kept running all
the time and a set of comparators is used to syn-
chronize turning on and off of the power MOS in
order to have zero current and zero voltage
switching and furthermore controlled rectification.
The step-up converter is designed to work in Lin-
ear mode, and an AC compensation network is
required (RC-comp) to guarantee the stability in a
wide operative range (i.e. changing coil, load,
output and input voltage...).
According to the ouput voltage, the current
loaded into the coil is changing like a Voltage
Loop-Current Controlled system, and in every
pulse there is a regulated power transfer to the
load.
The resonant LC topology has been chosen in or-
der to limit the voltage slew-rate across the coil
within reasonable values and so, to minimize ra-
diation problems.
The negative converter is a simple charge trans-
fer: it is supplied by the positive high voltage and
it capacitively translates this positive voltage
down to a negative one, obviously to limit radia-
tion problems also the charge output has a lim-
ited slew-rate; moreover to reduce intermodula-
tion
phoenomenas
the
charge
output
is
synchronized with the LC oscillations of the reso-
nant boost.
This negative voltage is (not counting drops on
external rectification diodes) in tracking with the
positive one and so the negative output controller
is not required.
If the drivers are supplied by HVP & HVM gener-
ated by external power supply the error amplifier
output has to be connected to V5/12.
In the external supply configuration the maximum
voltage between HVP and HVM (|HVP| + |HVM|)
must not exceed 70V and maximum voltage be-
tween GND and HVM must be lower than 35V.
Vin0-5
PIN11
Vosh
PIN10
VrefIN
0
0-VrefIN
VIN,MAX - VrefIN
VIN,MAX
VIN,MAX =
{
5.0V IF V5/12 > 5.5V
V5/12 - 0.5V IF V5/12
≤ 5.5V
Figure 4. Shifter DC transfer function
L6660
7/9



Html Pages

1 2 3 4 5 6 7 8 9


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com