| 数据搜索系统,热门电子元器件搜索 |
|
ATS672LSB 数据表(PDF) 4 Page - Allegro MicroSystems |
|
|
|||||||||||||||||||||||||||||
ATS672LSB 数据表(HTML) 4 Page - Allegro MicroSystems |
|
4 / 15 page ![]() 3 30Dec03, Rev. 1.42 Worcester, Massachusetts 01615-0036 (508) 853-5000 115 Northeast Cutoff, Box 15036 www.allegromicro.com Allegro MicroSystems, Inc. Self-Calibrating Gear Tooth Sensor with 9-Bit Signal Capture ATS672LSB OPERATING CHARACTERISTICS Valid at Ta = –40ºC to 150ºC, and VCC within specification, unless otherwise noted Characteristics Symbol Test Conditions Min. Typ. Max. Units Electrical Characteristics Supply Voltage VCC Operating; TJ < TJ(max) 3.3 – 26.5 V Reverse Supply Voltage VRCC IRCC = –5 mA, maximum – – –18 V Supply Zener Clamp Voltage VZSupply ICC = 14 mA (≈ICC(max) + 3 mA); TA = 25°C 28 – – V Output Zener Clamp Voltage VZOutput IOUT = 3 mA; TA = 25°C 30 – – V Supply Zener Current IZSupply Test conditions only; VCC = 28 V – – ICC(max) + 3 mA Output Zener Current IZOutput VOUT = 30 V – – 3 mA Supply Current ICC Output = OFF 3 6.5 11 mA Output = ON 3 6.5 11 mA Power-On State Characteristics Power-On Time tPO Gear Speed < 100 RPM; VCC > 3.3 V – – 500 µs Undervoltage Lockout VUV – – < VCC(min) V Output Stage Low Output Voltage VLOUT ISINK = 15 mA, Output = ON – 0.2 0.45 V Output Current Limit Ilim Output = ON; TJ < TJ(max) 25 45 70 mA Output Leakage Current IOFF Output = OFF; VOUT = VCC(max) – – 10 µA Output Rise Time tr RLOAD = 500 Ω; CLOAD = 10 pF; TA = 25°C – 0.9 5 µs Output Fall Time tf RLOAD = 500 Ω; CLOAD = 10 pF; TA = 25°C – 0.5 5 µs Switch Point Characteristics Tooth Speed Smax 0 – 8 kHz Bandwidth f – 3 dB – 40 – kHz Operate Point BOP % of peak-to-peak, referenced to tooth sensing signal; AG < AGMax –30 – % Release Point BRP % of peak-to-peak, referenced to tooth sensing signal; AG < AGMax –40 – % Output Polarity VOUT Valley opposite the sensor – HIGH – Tooth opposite the sensor – LOW – Calibration Initial Calibration CI Number of rising mechanical edges on the target that are required for accurate edge detection –2 3 AGC Disable Cf Number of rising mechanical edges on the target that are required to complete the AGC calibration –– 3 |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |