ST7LITEU09 datasheet(51/115 Pages) STMICROELECTRONICS

51 / 115 page

ST7LITEU05 ST7LITEU09

51/115

I/O PORTS (Cont’d)

CAUTION: The alternate function must not be ac-

tivated as long as the pin is configured as input

with interrupt, in order to avoid generating spurious

interrupts.

Analog alternate function

When the pin is used as an ADC input, the I/O

must be configured as floating input. The analog

multiplexer (controlled by the ADC registers)

switches the analog voltage present on the select-

ed pin to the common analog rail which is connect-

ed to the ADC input.

It is recommended not to change the voltage level

or loading on any port pin while conversion is in

progress. Furthermore it is recommended not to

have clocking pins located close to a selected an-

alog pin.

WARNING: The analog input voltage level must

be within the limits stated in the absolute maxi-

mum ratings.

10.3 UNUSED I/O PINS

Unused I/O pins must be connected to fixed volt-

age levels. Refer to Section 13.8.

10.4 LOW POWER MODES

10.5 INTERRUPTS

The external interrupt event generates an interrupt

if the corresponding configuration is selected with

DDR and OR registers and the interrupt mask in

the CC register is not active (RIM instruction).

10.6 I/O PORT IMPLEMENTATION

The hardware implementation on each I/O port de-

pends on the settings in the DDR and OR registers

and specific feature of the I/O port such as ADC In-

put or true open drain.

Switching these I/O ports from one state to anoth-

er should be done in a sequence that prevents un-

wanted side effects. Recommended safe transi-

tions are illustrated in Figure 33. Other transitions

are potentially risky and should be avoided, since

they are likely to present unwanted side-effects

such as spurious interrupt generation.

Figure 33. Interrupt I/O Port State Transitions

The I/O port register configurations are summa-

rised in the following table:

Table 17. Port Configuration

Notes:

IS4[1:0] = 01 is the only safe configuration to avoid spurious interrupt in HALT and AWUFH modes. Re-

fer to EICR2 description on page 33.

2. After reset, to configure PA3 as a general purpose output, the application has to program the MUXCR0 and MUXCR1

registers. See section 7.4 on page 30

Mode

Description

WAIT

No effect on I/O ports. External interrupts

cause the device to exit from WAIT mode.

HALT

No effect on I/O ports. External interrupts

cause the device to exit from HALT mode.

Interrupt Event

Event

Flag

Enable

Control

Bit

Exit

from

Wait

Exit

from

Halt

External interrupt on

selected external

event

DDRx

ORx

Yes

floating/pull-up

interrupt

INPUT

floating

(reset state)

INPUT

open-drain

OUTPUT

push-pull

OUTPUT

= DDR, OR

Port

Pin name

Input (DDR=0)

Output (DDR=1)

OR = 0

OR = 1

OR = 0

OR = 1

Port A

PA0:2, PA4:5 1)

floating

pull-up interrupt 1)

open drain

push-pull

PA3 2)

open drain

push-pull

ST7LITEU09 数据表(PDF) 51 Page - STMicroelectronics

ST7LITEU09 数据表(HTML) 51 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载

链接网址

ST7LITEU09 数据表(PDF) 51 Page - STMicroelectronics

ST7LITEU09 数据表(HTML) 51 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表 下载

链接网址

数据表下载