128 SAL-RPM

www.vishay.com

Vishay BCcomponents

Revision: 25-Oct-13

9

Document Number: 28354

For technical questions, contact: aluminumcaps2@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Table 3

TEST PROCEDURES AND REQUIREMENTS

TEST

PROCEDURE

(quick reference)

REQUIREMENTS

NAME OF TEST

REFERENCE

Endurance

IEC 60384-4/



EN130300



subclause 4.13

Tamb = 125 °C; 

UR = 6.3 V to 25 V with UR applied; 

UR = 40 V with UC applied;

10 000 h

C/C: ± 10 %

tan

  1.2 x spec. limit

Z

 1.2 x spec. limit

IL5  spec. limit

Useful life

CECC 30302



subclause 1.8.1

Tamb = 125 °C;

IR applied and:

UR = 6.3 V to 25 V with UR applied;

UR = 40 V with UC applied;

20 000 h

C/C: ± 15 %

tan

  1.5 x spec. limit

Z

 1.5 x spec. limit

IL5  spec. limit

no short or open circuit,



no visible damage

total failure percentage: < 1 %

Shelf life (storage at



high temperature)

IEC 60384-4/



EN130300



subclause 4.17

Tamb = 125 °C; no voltage applied;

500 h

C/C: ± 10 %

tan

  1.2 x spec. limit

IL5  spec. limit

Charge and discharge

IEC 60384-4-2



subclause 9.21

106 cycles without series resistance:

0.5 s to UR; 

0.5 s to ground

C/C: ± 5 %

no short or open circuit,



no visible damage

Solvent resistance

IEC 60068-2-45,



test XA



IEC 60653

Immersion: 5 min ± 0.5 min with or without

ultrasonic at 55 °C ± 5 °C

Solvents: demineralized water and/or calgonite

solution (20 g/l)

Visual appearance not affected

Extended vibration

IEC 60068-2-6



test Fc

10 Hz to 2000 Hz; 1.5 mm or 20 g;



1 octave/min; 3 directions;



1 sweep per direction; no voltage applied

no intermittent contacts

no breakdown

no open circuiting

no mechanical damage

C/C: ± 5 %

tan

  1.2 x spec. limit

Z

 1.2 x spec. limit

IL5  1.5 x spec. limit

Shock

IEC 60068-2-27



test Ea

Half-sine or sawtooth pulse shape; 50 g; 11 ms;



3 successive shocks in each direction of

3 mutually perpendicular axes;



no voltage applied

no intermittent contacts

no breakdown

no open circuiting

no mechanical damage

C/C: ± 5 %

tan

  1.2 x spec. limit

Z

 1.2 x spec. limit

IL5  1.5 x spec. limit

Passive flammability

IEC 60695-2-2

Capacitor mounted to a vertical printed-circuit

board, one flame on capacitor body;



Tamb = 20 °C to 25 °C;

test duration = 20 s

After removing the test flame from

the capacitor, the capacitor must

not continue to burn for more than

15 s; no burning particles must drop

from the sample