M50LPW040N datasheet(16/36 Pages) STMICROELECTRONICS

16 / 36 page

M50LPW040

16/36

Table 14. Low Pin Count Register Configuration Map (1)

Note: 1. This map is referred to the boot memory (ID0-ID2 floating or driven, LOW, VIL and A19-A21 set to ‘1’).

Mnemonic

Memory

Address

Default

Value

Access

T_BLOCK_LK

Top Block Lock Register (Block 7)

FFBF0002h

01h

R/W

T_MINUS01_LK

Top Block [-1] Lock Register (Block 6)

FFBE0002h

01h

R/W

T_MINUS02_LK

Top Block [-2] Lock Register (Block 5)

FFBD0002h

01h

R/W

T_MINUS03_LK

Top Block [-3] Lock Register (Block 4)

FFBC0002h

01h

R/W

T_MINUS04_LK

Top Block [-4] Lock Register (Block 3)

FFBB0002h

01h

R/W

T_MINUS05_LK

Top Block [-5] Lock Register (Block 2)

FFBA0002h

01h

R/W

T_MINUS06_LK

Top Block [-6] Lock Register (Block 1)

FFB90002h

01h

R/W

T_MINUS07_LK

Top Block [-7] Lock Register (Block 0)

FFB80002h

01h

R/W

GPI_REG

General Purpose Input Register

FFBC0100h

N/A

00h instead. When the Read Lock Bit is reset, ‘0’,

read operations in the Block return the data pro-

grammed into the block as expected.

After power-up or reset the Read Lock Bit is al-

ways reset to ‘0’ (not read protected).

Lock Down. The Lock Down Bit provides a

mechanism for protecting software data from sim-

ple hacking and malicious attack. When the Lock

Down Bit is set, ‘1’, further modification to the

Write Lock, Read Lock and Lock Down Bits cannot

be performed. A reset or power-up is required be-

fore changes to these bits can be made. When the

Lock Down Bit is reset, ‘0’, the Write Lock, Read

Lock and Lock Down Bits can be changed.

General Purpose Input Register

The General Purpose Input Register holds the

state of the General Purpose Input pins, GPI0-

GPI4. When this register is read, the state of these

pins is returned. This register is read-only and writ-

ing to it has no effect.

The signals on the General Purpose Input pins

should remain constant throughout the whole Bus

Read cycle in order to guarantee that the correct

data is read.

Write Lock. The

Write

Lock

Bit

determines

whether the contents of the Block can be modified

(using the Program or Block Erase Command).

When the Write Lock Bit is set, ‘1’, the block is

write protected; any operations that attempt to

change the data in the block will fail and the Status

Bit is reset, ‘0’, the block is not write protected

through the Lock Register and may be modified

unless write protected through some other means.

When VPP is less than VPPLK all blocks are pro-

tected and cannot be modified, regardless of the

state of the Write Lock Bit. If Top Block Lock, TBL,

is Low, VIL, then the Top Block (Block 7) is write

protected and cannot be modified. Similarly, if

Write Protect, WP, is Low, VIL, then the Main

Blocks (Blocks 0 to 6) are write protected and can-

not be modified.

After power-up or reset the Write Lock Bit is al-

ways set to ‘1’ (write protected).

Read Lock. The

Read

Lock

bit

determines

whether the contents of the Block can be read

(from Read mode). When the Read Lock Bit is set,

‘1’, the block is read protected; any operation that

attempts to read the contents of the block will read

M50LPW040N 数据表(PDF) 16 Page - STMicroelectronics

M50LPW040N 数据表(HTML) 16 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表下载