ST6208CB3 datasheet(39/70 Pages) STMICROELECTRONICS

39 / 70 page

39/70

ST62T08C/T09C ST62T10C/T20C/E20C

TIMER (Cont’d)

4.2.3 Application Notes

The user can select the presence of an on-chip

pull-up on the TIMER pin as option.

TMZ is set when the counter reaches zero; howev-

er, it may also be set by writing 00h in the TCR

The TMZ bit must be cleared by user software

when servicing the timer interrupt to avoid unde-

sired interrupts when leaving the interrupt service

routine. After reset, the 8-bit counter register is

loaded with 0FFh, while the 7-bit prescaler is load-

ed with 07Fh, and the TSCR register is cleared.

This means that the Timer is stopped (PSI=“0”)

and the timer interrupt is disabled.

If the Timer is programmed in output mode, the

DOUT bit is transferred to the TIMER pin when

TMZ is set to one (by software or due to counter

decrement). When TMZ is high, the latch is trans-

parent and DOUT is copied to the timer pin. When

TMZ goes low, DOUT is latched.

A write to the TCR register will predominate over

the 8-bit counter decrement to 00h function, i.e. if a

write and a TCR register decrement to 00h occur

simultaneously, the write will take precedence,

and the TMZ bit is not set until the 8-bit counter

reaches 00h again. The values of the TCR and the

PSC registers can be read accurately at any time.

4.2.4 Timer Registers

Timer Status Control Register (TSCR)

Address: 0D4h

—

Read/Write

Bit 7 = TMZ: Timer Zero bit

A low-to-high transition indicates that the timer

count register has decrement to zero. This bit must

be cleared by user software before starting a new

count.

Bit 6 = ETI: Enable Timer Interrupt

When set, enables the timer interrupt request

(vector #3). If ETI=0 the timer interrupt is disabled.

If ETI=1 and TMZ=1 an interrupt request is gener-

ated.

Bit 5 = TOUT: Timers Output Control

When low, this bit selects the input mode for the

TIMER pin. When high the output mode is select-

ed.

Bit 4 = DOUT: Data Output

Data sent to the timer output when TMZ is set high

(output mode only). Input mode selection (input

mode only).

Bit 3 = PSI: Prescaler Initialize Bit

Used to initialize the prescaler and inhibit its count-

ing. When PSI=“0” the prescaler is set to 7Fh and

the counter is inhibited. When PSI=“1” the prescal-

er is enabled to count downwards. As long as

PSI=“0” both counter and prescaler are not run-

ning.

Bit 2, 1, 0 = PS2, PS1, PS0: Prescaler Mux. Se-

lect. These bits select the division ratio of the pres-

caler register.

Table 13. Prescaler Division Factors

Timer Counter Register TCR

Address: 0D3h

—

Read/Write

Bit 7-0 = D7-D0: Counter Bits.

Prescaler Register PSC

Address: 0D2h

—

Read/Write

Bit 7 = D7: Always read as "0".

Bit 6-0 = D6-D0: Prescaler Bits.

TMZ

ETI

TOUT DOUT

PSI

PS2

PS1

PS0

PS2

PS1

PS0

Divided by

128

127

ST6208CB3 数据表(PDF) 39 Page - STMicroelectronics

ST6208CB3 数据表(HTML) 39 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

数据表下载

链接网址

ST6208CB3 数据表(PDF) 39 Page - STMicroelectronics

ST6208CB3 数据表(HTML) 39 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

数据表 下载

链接网址

数据表下载