ST72104G2 datasheet(129/135 Pages) STMICROELECTRONICS

129 / 135 page

ST72104G, ST72215G, ST72216G, ST72254G

129/135

15 DEVICE CONFIGURATION AND ORDERING INFORMATION

Each device is available for production in user pro-

grammable versions (FLASH) as well as in factory

coded versions (ROM). FLASH devices are

shipped to customers with a default content (FFh),

while ROM factory coded parts contain the code

supplied by the customer. This implies that FLASH

devices have to be configured by the customer us-

ing the Option Bytes while the ROM devices are

factory-configured.

15.1 OPTION BYTES

The two option bytes allow the hardware configu-

ration of the microcontroller to be selected.

The option bytes have no address in the memory

map and can be accessed only in programming

mode (for example using a standard ST7 program-

ming tool). The default content of the FLASH is

fixed to FFh.

In masked ROM devices, the option bytes are

fixed in hardware by the ROM code (see option

list).

USER OPTION BYTE 0

Bit 7:2 = Reserved, must always be 1.

Bit 1 = EXTIT

External Interrupt Configuration.

This option bit allows the external interrupt map-

ping to be configured as shown in Table 23.

Table 23. External Interrupt Configuration

Bit 0 = FMP

Full memory protection.

This option bit enables or disables external access

to the internal program memory (read-out protec-

tion). Clearing this bit causes the erasing (to 00h)

of the whole memory (including the option byte).

0: Program memory not read-out protected

1: Program memory read-out protected

USER OPTION BYTE 1

Bit 7 = CFC

Clock filter control on/off

This option bit enables or disables the clock filter

(CF) features.

0: Clock filter enabled

1: Clock filter disabled

Bit 6:4 = OSC[2:0]

Oscillator selection

These three option bits can be used to select the

main oscillator as shown in Table 24.

Bit 3:2 = LVD[1:0]

Low voltage detection selection

These option bits enable the LVD block with a se-

lected threshold as shown in Table 25.

Bit 1 = WDG HALT

Watchdog and halt mode

This option bit determines if a RESET is generated

when entering HALT mode while the Watchdog is

active.

0: No Reset generation when entering Halt mode

1: Reset generation when entering Halt mode

Bit 0 = WDG SW

Hardware or software watchdog

This option bit selects the watchdog type.

0: Hardware (watchdog always enabled)

1: Software (watchdog to be enabled by software)

Table 24. Main Oscillator Configuration

Table 25. LVD Threshold Configuration

External IT0

External IT1

EXTIT

Ports PA7-PA0

Ports PB7-PB0

Ports PC5-PC0

Ports PA7-PA0

Ports PC5-PC0

Ports PB7-PB0

Selected Oscillator

OSC2 OSC1 OSC0

External Clock (Stand-by)

~4 MHz Internal RC

1~14 MHz External RC

Low Power Resonator (LP)

Medium Power Resonator (MP)

Medium Speed Resonator (MS)

High Speed Resonator (HS)

Configuratio n

LVD1 LVD0

LVD Off

Highest Voltage Threshold (

∼4.50V)

Medium Voltage Threshold (

∼4.05V)

Lowest Voltage Threshold (

∼3.45V)

USER OPTIO N BYTE 0

USER OPTIO N BYTE 1

Reserved

EXTIT FMP

CFC

OSC

LVD1 LVD0

WDG

HALT

WDG

Default

Value

1111

111

ST72104G2 数据表(PDF) 129 Page - STMicroelectronics

ST72104G2 数据表(HTML) 129 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载