| 数据搜索系统,热门电子元器件搜索 |
|
L9380 数据表(PDF) 9 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
L9380 数据表(HTML) 9 Page - STMicroelectronics |
|
9 / 18 page ![]() L9380 Functional description 9/18 4 Functional description The triple high-side Power-MOS Driver features all necessary control and protection functions to switch on three Power-MOS transistors operating as High-Side switches in automotive electronic control units. The key application field is relays replacement in systems where high current loads, usually motors with nominal currents of about 40 A connected to ground, has to be switched. A high signal at the EN pin enables all three channels. With enable low gates are clamped to ground. In this condition the gate sink current is higher than the specified 3 mA. An enable low signal makes also a reset of the timer. A low signal at the inputs switch on the gates of the external MOS. A short circuit at the input leads to permanent activation of the concerned channel. In this case the device can be disabled with the enable pin. The charge pump loading is not influenced due to the enable input. An external N-channel MOS driver in high side configuration needs a gate driving voltage higher than VS. It is generated by means of a charge pump with integrated charge transfer capacitors and one external charge storage capacitor CCP. The charge pump is dimensioned to load a capacitor CCP of 33 nF in less than 20 ms up to 8V above VS. The value of CCP depends on the input capacitance of the external MOS and the decay of the charge pump voltage down to that value where no significant influence on the application occurs. The necessary charging time for CCP has to be respected in the sequence of the input control signals. As a consequence the lower gate to source voltage can cause a higher drop across the Power-MOS and get into overload condition. In this case the overload protection timer will start. After the protection time the concerned channel will be switched off. Channel 3 is not equipped with an overload protection. The same situation can occur due to a discharge of the storage capacitor caused by the gate short to ground. The gate driver that is supplied from the pin CP, which is the charge pump output, has a sink and source current capability of 3 mA. For a short-circuit of the load (source to ground) the L9380 has no gate to source limitation. The gate source protection must be done externally. Channel 1 and 2 provide drain to source voltage sensing possibility with programmable shut-off delay when the activation threshold was exceeded. This threshold VDSmin is set by the external resistor RD. The bias current flowing through this resistor is determined by the programming resistor RPR. This external resistor RPR defines also the charge and discharge current of the timer capacitor CCT. The drain to source threshold VDSmin and the timer shut off delay time Toff can be calculated: Toff = 4.4 CT RPR V DSmin V PR R D R PR ------------ ⎝⎠ ⎜⎟ ⎛⎞ = |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |