STPC0366BTI3 datasheet(20/51 Pages) STMICROELECTRONICS

20 / 51 page

PIN DESCRIPTION

20/51

Issue 1.2

ed to ISAOE# and the output is provided with a

weak pull-up resistor.

RTCRW# / DD[13]

Real Time Clock RW. This pin

is a multi-function pin. When ISAOE# is active,

this signal is used as RTCRW#. This signal is as-

serted for any I/O write to port 71H.

When ISAOE# is inactive, this signal is used as

IDE DD[13] signal.

This signal must be ORed externally with ISAOE#

and then connected to the RTC. An LS244 or

equivalent function can be used if OE is connect-

ed to ISAOE# and the output is provided with a

weak pull-up resistor.

RTCDS# / DD[12]

Real Time Clock DS. This pin is

a multi-function pin. When ISAOE# is active, this

signal is used as RTCDS. This signal is asserted

for any I/O read to port 71H.

When ISAOE# is inactive, this signal is used as

IDE DD[12] signal.

This signal must be ORed externally with ISAOE#

and is then connected to RTC. An LS244 or equiv-

alent function can be used if OE# is connected to

ISAOE# and the output is provided with a weak

pull-up resistor.

RTCAS#

Real time clock address strobe. This sig-

nal is asserted for any I/O write to port 70H.

2.2.12 Monitor Interface

RED, GREEN, BLUE

RGB Video Outputs. These

are the 3 analog color outputs from the RAMDACs

VSYNC

Vertical Synchronisation Pulse. This is

the vertical synchronization signal from the VGA

controller.

HSYNC

Horizontal Synchronisation Pulse. This is

the horizontal synchronization signal from the

VGA controller.

VREF_DAC

DAC Voltage reference. An external

voltage reference is connected to this pin to bias

the DAC.

RSET

Resistor Current Set. This is reference cur-

rent input to the RAMDAC is used to set the full-

scale output of the RAMDAC.

COMP

Compensation. This is the RAMDAC com-

pensation pin. Normally, an external capacitor

(typically 10nF) is connected between this pin and

VDD to damp oscillations.

DDC[1:0]

Direct Data Channel Serial Link. These

bidirectional pins are connected to CRTC register

3Fh to implement DDC capabilities. They conform

to I2C electrical specifications, they have open-

collector output drivers which are internally con-

nected to VDD through pull-up resistors.

They can instead be used for accessing I C devic-

es on board. DDC1 and DDC0 correspond to SCL

and SDA respectively.

COL_CMP

Color Compare Output. Allows access

to the video signal which flags when there is a

color compare hit. This signal is multiplexed with

SMEMEW# on the ISA Bus. The signal is selected

by setting Strap Option MD[0] as described in Sec-

tion 3.

2.2.13 MISCELLANEOUS

SCAN_ENABLE

Reserved. The pins are re-

served for Test and Miscellaneous functions)

STPC0366BTI3 数据表(PDF) 20 Page - STMicroelectronics

STPC0366BTI3 数据表(HTML) 20 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

数据表下载