MCP6271-ESLASHMS datasheet(2/36 Pages) MICROCHIP

2 / 36 page

MCP6271/1R/2/3/4/5

DS21810F-page 2

1.0

ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

VDD –VSS ........................................................................7.0V

Current at Input Pins ....................................................±2 mA

Analog Inputs (VIN+ and VIN–) †† .. VSS –1.0VtoVDD +1.0V

All other Inputs and Outputs .......... VSS – 0.3V to VDD +0.3V

Difference Input Voltage ...................................... |VDD –VSS|

Output Short Circuit Current .................................Continuous

Current at Output and Supply Pins ............................±30 mA

Storage Temperature.................................... –65°C to +150°C

Junction Temperature (TJ) ..........................................+150°C

ESD Protection On All Pins (HBM/MM)

................ ≥ 4 kV/400V

† Notice: Stresses above those listed under “Absolute

Maximum Ratings” may cause permanent damage to the

device. This is a stress rating only and functional operation of

the device at those or any other conditions above those

indicated in the operational listings of this specification is not

implied. Exposure to maximum rating conditions for extended

periods may affect device reliability.

†† See Section 4.1.2 “Input Voltage and Current Limits”.

DC ELECTRICAL SPECIFICATIONS

Electrical Characteristics: Unless otherwise indicated, TA = +25°C, VDD = +2.0V to +5.5V, VSS = GND, VCM =VDD/2,

VOUT ≈ VDD/2, VL = VDD/2, RL =10 kΩ to VL and CS is tied low. (Refer to Figure 1-2 and Figure 1-3).

Parameters

Sym

Min

Typ

Max

Units

Conditions

Input Offset (Note 1)

Input Offset Voltage

VOS

–3.0

—

+3.0

VCM = VSS

Input Offset Voltage

(Extended Temperature)

VOS

–5.0

—

+5.0

TA = –40°C to +125°C, VCM = VSS

Input Offset Temperature Drift

ΔV

OS/ΔTA

—±1.7

—

µV/°C TA = –40°C to +125°C, VCM = VSS

Power Supply Rejection Ratio

PSRR

—

VCM = VSS

Input Bias Current and Impedance

Input Bias Current

—

±1.0

—

Note 2

At Temperature

—

200

TA= +85°C (Note 2)

At Temperature

—2

TA= +125°C (Note 2)

Input Offset Current

IOS

—

±1.0

—

Note 3

Common Mode Input Impedance

ZCM

—1013||6

—

Ω||pF Note 3

Differential Input Impedance

ZDIFF

—1013||3

—

Ω||pF Note 3

Common Mode (Note 4)

Common Mode Input Voltage Range

VCMR

VSS − 0.15

—

VDD +0.15

VDD = 2.0V (Note 5)

VCMR

VSS − 0.30

—

VDD +0.30

VDD = 5.5V (Note 5)

Common Mode Rejection Ratio

CMRR

—

VCM = –0.3V to 2.5V, VDD = 5V

(Note 6)

Common Mode Rejection Ratio

CMRR

—

VCM = –0.3V to 5.3V, VDD = 5V

(Note 6)

Open-Loop Gain

DC Open-Loop Gain (Large Signal)

AOL

110

—

VOUT = 0.2V to VDD – 0.2V,

VCM =VSS (Note 1)

Note

The MCP6275’s VCM for op amp B (pins VOUTA/VINB+ and VINB–) is VSS +100 mV.

The current at the MCP6275’s VINB– pin is specified by IB only.

This specification does not apply to the MCP6275’s VOUTA/VINB+ pin.

The MCP6275’s VINB– pin (op amp B) has a common mode input voltage range (VCMR) of VSS + 100 mV to

VDD – 100 mV. CMRR is not measured for op amp B of the MCP6275. The MCP6275’s VOUTA/VINB+ pin (op amp B)

has a voltage range specified by VOH and VOL.

Set by design and characterization.

Does not apply to op amp B of the MCP6275.

All parts with date codes November 2007 and later have been screened to ensure operation at VDD = 6.0V. However,

the other minimum and maximum specifications are measured at 2.0V and 5.5V.

MCP6271-E/MS 数据表(PDF) 2 Page - Microchip Technology

MCP6271-E/MS 数据表(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表下载