ADRF6601ACPZ-R7 datasheet(3/24 Pages) AD

3 / 24 page

ADRF6601

Rev. 0 | Page 3 of 24

SPECIFICATIONS

RF SPECIFICATIONS

VCCx = 5 V; ambient temperature (TA) = 25°C; fREF = 38.4 MHz; fPFD = 38.4 MHz; high-side LO injection; fIF = 140 MHz; IIP3 optimized

using CDAC = 0x1 and IP3SET = 3.3 V, unless otherwise noted.

Table 2.

Parameter

Test Conditions/Comments

Min

Typ

Max

Unit

INTERNAL LO FREQUENCY RANGE

750

1160

MHz

RF INPUT FREQUENCY RANGE

±3 dB RF input range

300

2500

MHz

RF INPUT AT 610 MHz

Input Return Loss

Relative to 50 Ω (can be improved with external match)

−14

Input P1dB

14.3

dBm

Second-Order Intercept (IIP2)

−5 dBm each tone (10 MHz spacing between tones)

dBm

Third-Order Intercept (IIP3)

−5 dBm each tone (10 MHz spacing between tones)

32.5

dBm

Single-Side Band Noise Figure

IP3SET = 3.3 V

13.0

IP3SET = open

12.2

LO-to-IF Leakage

At 1× LO frequency, 50 Ω termination at the RF port

−51

dBm

RF INPUT AT 910 MHz

Input Return Loss

Relative to 50 Ω (can be improved with external match)

−18

Input P1dB

14.3

dBm

Second-Order Intercept (IIP2)

−5 dBm each tone (10 MHz spacing between tones)

dBm

Third-Order Intercept (IIP3)

−5 dBm each tone (10 MHz spacing between tones)

31.0

dBm

Single-Side Band Noise Figure

IP3SET = 3.3 V

14.0

IP3SET = open

13.1

LO-to-IF Leakage

At 1× LO frequency, 50 Ω termination at the RF port

−51

dBm

RF INPUT AT 1020 MHz

Low-side injection

Input Return Loss

Relative to 50 Ω (can be improved with external match)

−16

Input P1dB

14.3

dBm

Second-Order Intercept (IIP2)

−5 dBm each tone (10 MHz spacing between tones)

dBm

Third-Order Intercept (IIP3)

−5 dBm each tone (10 MHz spacing between tones)

31.5

dBm

Single-Side Band Noise Figure

IP3SET = 3.3 V

14.5

IP3SET = open

13.5

LO-to-IF Leakage

At 1× LO frequency, 50 Ω termination at the RF port

−45

dBm

IF OUTPUT

Voltage Conversion Gain

Differential 200 Ω load

6.7

IF Bandwidth

Small-signal 3 dB bandwidth

500

MHz

Output Common-Mode Voltage

External pull-up balun or inductors required

Gain Flatness

Over frequency range, any 5 MHz/50 MHz

0.2/1.0

Gain Variation

Over full temperature range

1.0

Output Swing

Differential 200 Ω load

V p-p

Output Return Loss

Relative to 200 Ω

−15

LO INPUT/OUTPUT (LOP, LON)

Externally applied 1× LO input, internal PLL disabled

Frequency Range

250

6000

MHz

Output Level (LO as Output)

1× LO into a 50 Ω load, LO output buffer enabled

−5.5

dBm

Input Level (LO as Input)

±6

dBm

Input Impedance

ADRF6601ACPZ-R7 数据表(PDF) 3 Page - Analog Devices

ADRF6601ACPZ-R7 数据表(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表下载

链接网址

ADRF6601ACPZ-R7 数据表(PDF) 3 Page - Analog Devices

ADRF6601ACPZ-R7 数据表(HTML) 3 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

数据表 下载

链接网址

数据表下载