TOP243Y datasheet(12/48 Pages) POWERINT

12 / 48 page

TOP242-249

7/01

August 8, 2000

✔

✔✔

✔

✔✔

✔

✔✔

✔

✔✔

✔

✔✔✔

✔

Table 3. Typical MULTI-FUNCTION Pin Configurations.

MULTI-FUNCTION PIN TABLE*

*This table is only a partial list of many MULTI-FUNCTION pin configurations that are possible.

Figure Number

Three Terminal Operation

Under-Voltage

Overvoltage

Line Feed Forward (DC

MAX)

Overload Power Limiting

External Current Limit

Remote ON/OFF

11 for a description of the functions where the horizontal axis

(left hand side) represents the EXTERNAL CURRENT LIMIT

pin current. The meaning of the vertical axes varies with

function. For those that control the on/off states of the output

such as remote ON/OFF, the vertical axis represents the enable/

disable states of the output. For external current limit, the

vertical axis represents the magnitude of the I

LIMIT.

Please see

graphs in the typical performance characteristics section for the

current limit programming range and the selection of appropriate

resistor value.

MULTI-FUNCTION (M) Pin Operation (P and G Packages)

The LINE-SENSE and EXTERNAL CURRENT LIMIT pin

functions are combined to a single MULTI-FUNCTION pin for

P and G packages. The comparator with a 1 V threshold at the

LINE-SENSE pin is removed in this case as shown in Figure 2b.

All of the other functions are kept intact. However, since some

of the functions require opposite polarity of input current

(MULTI-FUNCTION pin), they are mutually exclusive. For

example, line sensing features cannot be used simultaneously

with external current limit setting. When current is fed into the

MULTI-FUNCTION pin, it works as a voltage source of

approximately 2.6 V up to a maximum current of +400

µA

(typical). At +400

µA,thispinturnsintoaconstantcurrentsink.

When current is drawn out of the MULTI-FUNCTION pin, it

works as a voltage source of approximately 1.3 V up to a

maximum current of –240

µA (typical). At –240 µA, it turns

into a constant current source. Refer to Figure 12b.

There are a total of five functions available through the use of

the MULTI-FUNCTION pin: OV, UV, line feed forward with

MAX reduction, external current limit and remote ON/OFF. A

short circuit between the MULTI-FUNCTION pin and

SOURCE pin disables all five functions and forces

TOPSwitch-GX to operate in a simple three terminal mode like

TOPSwitch-II. The MULTI-FUNCTION pin is typically used

for line sensing by connecting a resistor from this pin to the

rectified DC high voltage bus to implement OV, UV and DC

MAX

reduction with line voltage. In this mode, the value of the

resistor determines the line OV/UV thresholds, and the DC

MAX

is reduced linearly with rectified DC high voltage starting from

just above the UV threshold. In high efficiency applications

this pin can be used in the external current limit mode instead,

to reduce the current limit externally to a value close to the

operating peak current, by connecting the pin to the SOURCE

pin through a resistor. The same pin can also be used as a remote

on/off and a synchronization input in both modes. Please refer

to Table 3 for possible combinations of the functions with

example circuits shown in Figure 30 through Figure 40. A

description of specific functions in terms of the MULTI-

FUNCTION pin I/V characteristic is shown in Figure 11. The

horizontal axis represents MULTI-FUNCTION pin current

with positive polarity indicating currents flowing into the pin.

The meaning of the vertical axes varies with functions. For

those that control the on/off states of the output such as UV, OV

and remote ON/OFF, the vertical axis represents the enable/

disable states of the output. UV triggers at I

UV (+50 µA typical)

and OV triggers at I

OV (+225 µA typical with 30 µA hysteresis).

Between the UV and OV thresholds, the output is enabled. For

external current limit and line feed forward with DC

MAX

reduction, the vertical axis represents the magnitude of the I

LIMIT

and DC

MAX.

Line feed forward with DC

MAX reduction lowers

maximum duty cycle from 78% at I

M(DC) (+60 µA typical) to 38%

at I

OV (+225 µA).

External current limit is available only with

negative MULTI-FUNCTION pin current. Please see graphs in

the typical performance characteristics section for the current

limit programming range and the selection of appropriate resistor

value.

TOP243Y 数据表(PDF) 12 Page - Power Integrations, Inc.

TOP243Y 数据表(HTML) 12 Page - Power Integrations, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

数据表下载