P89LPC9211FDH datasheet(32/75 Pages) NXP

32 / 75 page

P89LPC92X1

All information provided in this document is subject to legal disclaimers.

Product data sheet

Rev. 2 — 1 December 2010

32 of 75

NXP Semiconductors

P89LPC9201/9211/922A1/9241/

8-bit microcontroller with 8-bit ADC

7.16 I/O ports

The P89LPC9201/9211/922A1/9241/9251 has four I/O ports: Port 0, Port 1 and Port 3.

Ports 0 and 1 are 8-bit ports, and Port 3 is a 2-bit port. The exact number of I/O pins

available depends upon the clock and reset options chosen, as shown in Table 9.

7.16.1 Port configurations

All but three I/O port pins on the P89LPC9201/9211/922A1/9241/9251 may be configured

by software to one of four types on a bit-by-bit basis. These are: quasi-bidirectional

(standard 80C51 port outputs), push-pull, open drain, and input-only. Two configuration

registers for each port select the output type for each port pin.

1. P1.5 (RST) can only be an input and cannot be configured.

2. P1.2 (SCL/T0) and P1.3 (SDA/INT0) may only be configured to be either input-only or

open-drain.

7.16.1.1

Quasi-bidirectional output configuration

Quasi-bidirectional output type can be used as both an input and output without the need

to reconfigure the port. This is possible because when the port outputs a logic HIGH, it is

weakly driven, allowing an external device to pull the pin LOW. When the pin is driven

LOW, it is driven strongly and able to sink a fairly large current. These features are

somewhat similar to an open-drain output except that there are three pull-up transistors in

the quasi-bidirectional output that serve different purposes.

The P89LPC9201/9211/922A1/9241/9251 is a 3 V device, but the pins are 5 V tolerant. In

quasi-bidirectional mode, if a user applies 5 V on the pin, there will be a current flowing

from the pin to VDD, causing extra power consumption. Therefore, applying 5 V in

quasi-bidirectional mode is discouraged.

A quasi-bidirectional port pin has a Schmitt trigger input that also has a glitch suppression

circuit.

7.16.1.2

Open-drain output configuration

The open-drain output configuration turns off all pull-ups and only drives the pull-down

transistor of the port driver when the port latch contains a logic 0. To be used as a logic

output, a port configured in this manner must have an external pull-up, typically a resistor

tied to VDD.

Table 9.

Number of I/O pins available

Clock source

Reset option

Number of I/O

pins (28-pin

package)

On-chip oscillator or watchdog

oscillator

No external reset (except during

power-up)

External RST pin supported

External clock input

No external reset (except during

power-up)

External RST pin supported

Low/medium/high speed

oscillator (external crystal or

resonator)

No external reset (except during

power-up)

External RST pin supported

P89LPC9211FDH 数据表(PDF) 32 Page - NXP Semiconductors

P89LPC9211FDH 数据表(HTML) 32 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

数据表下载

链接网址

P89LPC9211FDH 数据表(PDF) 32 Page - NXP Semiconductors

P89LPC9211FDH 数据表(HTML) 32 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

数据表 下载

链接网址

数据表下载