HCS361 datasheet(14/42 Pages) MICROCHIP

14 / 42 page

HCS361

DS40146F-page 14

5.0

SPECIAL FEATURES

5.1

Code Word Completion

Code word completion is an automatic feature that

ensures that the entire code word is transmitted, even

if the button is released before the transmission is com-

plete and that a minimum of two words are completed.

The HCS361 encoder powers itself up when a button is

pushed and powers itself down after the current trans-

mission is finished, if the user has already released the

button. If the button is held down beyond the time for

two transmissions, then multiple transmissions will

result. The HCS361 transmits at least two transmis-

sions before powering down. If another button is acti-

vated during a transmission, the active transmission

will be aborted and the new code will be generated

using the new button information.

5.2

Blank Alternate Code Word

Federal Communications Commission (FCC) part 15

rules specify the limits on fundamental power and

harmonics that can be transmitted. Power is calculated

on the worst case average power transmitted in a 100

ms window. It is therefore advantageous to minimize

the duty cycle of the transmitted word. This can be

achieved by minimizing the duty cycle of the individual

bits and by blanking out consecutive words. Blank

Alternate Code Word (BACW) is used for reducing the

average power of a transmission (Figure 5-1). This is a

selectable feature. Using the BACW allows the user to

transmit a higher amplitude transmission if the

transmission length is shorter. The FCC puts

constraints on the average power that can be

transmitted by a device, and BACW effectively

prevents continuous transmission by only allowing the

transmission of every second word. This reduces the

average power transmitted and hence, assists in FCC

approval of a transmitter device.

5.3

CRC (Cycle Redundancy Check)

Bits

The CRC bits are calculated on the 65 previously trans-

mitted bits. The CRC bits can be used by the receiver

to check the data integrity before processing starts. The

CRC can detect all single bit and 66% of double bit

errors. The CRC is computed as follows:

EQUATION 5-1:

CRC Calculation

and

with

and

Din the nth transmission bit 0 ð n ð 64

FIGURE 5-1:

BLANK ALTERNATE CODE WORD (BACW)

Note: The CRC may be wrong when the battery

voltage is around either of the VLOW trip

points. This may happen because VLOW is

sampled twice each transmission, once for

the CRC calculation (PWM is low) and once

when VLOW is transmitted (PWM is high).

VDD tends to move slightly during a transmis-

sion which could lead to a different value for

VLOW being used for the CRC calculation

and the transmission

Work around: If the CRC calculation is incor-

rect, recalculate for the opposite value of

VLOW.

CRC 1

[]n 1

CRC 0

[]n Din

∧

CRC 0

[]n 1

CRC 0

[]n Din

∧

() CRC 1

[]n

∧

CRC 10

[]0

Code Word

BRS = 0

BRS = 1

Time

Code Word

Amplitude

HCS361 数据表(PDF) 14 Page - Microchip Technology

HCS361 数据表(HTML) 14 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表下载

链接网址

HCS361 数据表(PDF) 14 Page - Microchip Technology

HCS361 数据表(HTML) 14 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表 下载

链接网址

数据表下载