数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

ADP5023ACPZ-1-R7 数据表(PDF) 20 Page - Analog Devices

部件名 ADP5023ACPZ-1-R7
功能描述  Dual 3 MHz, 800 mA Buck
PDF  28 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  AD [Analog Devices]
网页  http://www.analog.com
标志 AD - Analog Devices

ADP5023ACPZ-1-R7 数据表(HTML) 20 Page - Analog Devices

Back Button ADP5023ACPZ-1-R7 Datasheet HTML 16Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 17Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 18Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 19Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 20Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 21Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 22Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 23Page - Analog Devices ADP5023ACPZ-1-R7 Datasheet HTML 24Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 20 / 28 page
background image
ADP5023
Data Sheet
Rev. A | Page 20 of 28
the input conditions change again and the required duty cycle
falls, the buck immediately restarts PWM regulation without
allowing overshoot on the output voltage.
Active Pull-Downs
All regulators have optional, factory-programmable, active pull-
down resistors discharging the respective output capacitors
when the regulators are disabled. The pull-down resistors are
connected between VOUTx and AGND. Active pull-downs are
disabled when the regulators are turned on. The typical value of
the pull-down resistor is 600 Ω for the LDO and 75 Ω for the
bucks. Figure 46 shows the activation timings for the active
pull-downs during regulator activation and deactivation.
LDO
The ADP5023 contains one LDO with low quiescent current
and low dropout voltage, and provides up to 300 mA of output
current. Drawing a low 10 μA quiescent current (typical) at no
load makes the LDO ideal for battery-operated portable
equipment.
The LDO operates with an input voltage of 1.7 V to 5.5 V. The
wide operating range makes these LDO suitable for cascading
configurations where the LDO supply voltage is provided from
one of the buck regulators.
The LDO output voltage is set through external resistor dividers
as shown in Figure 48 for LDO. The output voltage can
optionally be factory programmed to default values as indicated
in the Ordering Guide section. In this event, Ra and Rb are not
needed, and FB3 must be connected to the top of the capacitor on
VOUT3. FB3 is 0.5 V.
LDO
FB3
Ra
Rb
VOUT3
VOUT3
VIN3
C7
1µF
VOUT3 = VFB3
+ 1
Ra
Rb
Figure 48. LDO External Output Voltage Setting
The LDO also provides high power supply rejection ratio
(PSRR), low output noise, and excellent line and load transient
response with only a small 1 µF ceramic input and output
capacitor.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com