ThunderLAN

™ TNETE100

PCI ETHERNET

™ CONTROLLER

SINGLE-CHIP 10 BASE-T WITH MII FOR 100 BASE-T/100VG-AnyLAN

™

SPWS017B – APRIL 1995 – REVISED AUGUST 1996

7

POST OFFICE BOX 1443

Pin Functions (Continued)

PIN

TYPE†

DESCRIPTION

NAME

NO.

TYPE†

DESCRIPTION

PCI INTERFACE (CONTINUED)

PREQ

134

I/O

PCI bus request. PREQ is asserted by the TNETE100 to request control of the PCI bus. This is not a

shared signal.

PRST

129

I

PCI reset signal

PSERR

25

O/D

PCI system error. PSERR indicates parity errors or special-cycle data-parity errors.

PSTOP

23

I/O

PCI stop. PSTOP indicates the current target is requesting the master to stop the current transaction.

BIOS ROM / LED DRIVER INTERFACE

EAD7

EAD6

EAD5

EAD4

EAD3

EAD2

EAD1

EAD0

54

55

56

57

59

60

61

62

I/O

EPROM address / data. EAD[7:0] is a multiplexed byte bus that is used to address and read data from

an external BIOS ROM.

• On the cycle when EXLE is asserted low, EAD[7:0] is driven with the high byte of the

address.

• On the cycle when EALE is asserted low, EAD[7:0] is driven with the low byte of the

address.

• When EOE is asserted, BIOS ROM data should be placed on the bus.

These pins can be used also to drive external status LEDs. Low-current (2 – 5 mA) LEDs can be

connected directly (through appropriate resistors). High-current LEDs can be driven through buffers

or from the BIOS ROM address latches.

EALE

65

O

EPROM address latch enable. EALE is driven low to latch the low (least significant) byte of the BIOS

ROM address from EAD[0 :7].

EOE

64

O

EPROM output enable. When EOE is active (low), EAD[0 :7] is 3-stated, and the output of the BIOS

ROM should be placed on EAD[0 :7].

EXLE

66

O

EPROM extended address-latch enable. EXLE is driven low to latch the high (most significant) byte

of the BIOS ROM address from EAD[0 :7].

CONFIGURATION EEPROM INTERFACE

EDCLK

68

O

EEPROM data clock. EDCLK transfers serial clocked data to the 2K-bit serial EEPROMs (24C02) (see

Note 1).

EDIO

69

I/O

EEPROM data I / O. EDIO is the bidirectional serial data / address line to the 2K-bit serial EEPROM

(24C02). EDIO requires an external pullup for EEPROM operation. Tying EDIO to ground disables the

EEPROM interface and prevents autoconfiguration of the PCI configuration register.

MEDIA-INDEPENDENT INTERFACE (100-Mbps CSMA / CD AND DEMAND PRIORITY)

MCOL

80

I

Collision sense

• In CSMA/CD mode, assertion of MCOL indicates a network collision.

• In demand-priority mode, MCOL (active low) is used to acknowledge a transmission request.

The TNETE100 begins frame transmission 50 MTCLK cycles after the assertion (low) of MCOL.

MCRS

81

I

Carrier sense. MCRS indicates a frame-carrier signal is being received.

MDCLK

91

O

Management data clock. MDCLK is part of the serial management interface to physical-media

independent (PMI) / PHY chip.

MDIO

93

I/O

Management data I / O. MDIO is part of the serial management interface to PMI / PHY chip.

MRCLK

82

I

Receive clock. MRCLK is the receive clock source from the attached PHY and PMI device.

MRST

95

O

MII reset. MRST is the reset signal to the PMI / PHY front-end (active low).

† I = input, O = output, I / O = 3-state input / output, O / D = open-drain output

NOTE 1: This pin should be tied to VDD with a 4.7-kW – 10-kW pullup resistor.