ADSP2184 datasheet(13/31 Pages) AD

13 / 31 page

–13–

ADSP-2184

REV. 0

RECOMMENDED OPERATING CONDITIONS

B Grade

Parameter

Min

Max

Unit

VDD

4.5

5.5

TAMB

–40

+85

°C

ELECTRICAL CHARACTERISTICS

B Grade

Parameter

Test Conditions

Min

Typ

Max

Unit

VIH

Hi-Level Input Voltage1, 2

@ VDD = max

2.0

VIH

Hi-Level CLKIN Voltage

@ VDD = max

2.2

VIL

Lo-Level Input Voltage1, 3

@ VDD = min

0.8

VOH

Hi-Level Output Voltage1, 4, 5

@ VDD = min

IOH = –0.5 mA

2.4

@ VDD = min

IOH = –100 µA

VDD – 0.3

VOL

Lo-Level Output Voltage1, 4, 5

@ VDD = min

IOL = 2 mA

0.4

IIH

Hi-Level Input Current3

@ VDD = max

VIN = VDD max

µA

IIL

Lo-Level Input Current3

@ VDD = max

VIN = 0 V

µA

IOZH

Three-State Leakage Current7

@ VDD = max

VIN = VDD max

µA

IOZL

Three-State Leakage Current7

@ VDD = max

VIN = 0 V

8, t

CK = 25 ns

µA

IDD

Supply Current (Idle)9

@ VDD = 5.0

IDD

Supply Current (Dynamic)10, 11

@ VDD = 5.0

TAMB = +25°C

tCK = 25 ns

Input Pin Capacitance3, 6, 12

@ VIN = 2.5 V,

fIN = 1.0 MHz,

TAMB = +25°C

Output Pin Capacitance6, 7, 12, 13

@ VIN = 2.5 V,

fIN = 1.0 MHz,

TAMB = +25°C8

NOTES

1 Bidirectional pins: D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1–A13, PF0–PF7.

2 Input only pins:

RESET, BR, DR0, DR1, PWD.

3 Input only pins: CLKIN,

RESET, BR, DR0, DR1, PWD.

4 Output pins:

BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK, A0, DT0, DT1, CLKOUT, FL2-0, BGH.

5 Although specified for TTL outputs, all ADSP-2184 outputs are CMOS-compatible and will drive to V

DD and GND, assuming no dc loads.

6 Guaranteed but not tested.

7 Three-statable pins: A0–A13, D0–D23,

PMS, DMS, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RSF1, PF0–PF7.

8 0 V on

BR.

9 Idle refers to ADSP-2184 state of operation during execution of IDLE instruction. Deasserted pins are driven to either V

DD or GND.

10 I

DD measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (types 1, 4, 5, 12, 13, 14), 30% are type 2

and type 6, and 20% are idle instructions.

11 V

IN = 0 V and 3 V. For typical figures for supply currents, refer to Power Dissipation section.

12 Applies to LQFP package type.

13 Output pin capacitance is the capacitive load for any three-stated output pin.

Specifications subject to change without notice.

SPECIFICATIONS

ADSP2184 数据表(PDF) 13 Page - Analog Devices

ADSP2184 数据表(HTML) 13 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

数据表下载

链接网址

ADSP2184 数据表(PDF) 13 Page - Analog Devices

ADSP2184 数据表(HTML) 13 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

数据表 下载

链接网址

数据表下载