ACT8600 datasheet(3/5 Pages) AEROFLEX

3 / 5 page

Aeroflex Circuit Technology

ACT8600 REV A 9/16/99 Plainview NY (516) 694-6700

Adjustment Pin Current

Change con’t

∆IADJ

3V < VDIFF < 40V, TA = + 25°C

±5

µA

3.3V < VDIFF < 40V

±5

µA

Minimum Load Current

ILMIN

VDIF = 3.0V, VOUT = 1.4 (forced), TA = + 25°C

VDIF = 3.3V, VOUT = 1.4 (forced)

VDIF = 40V, VOUT = 1.4 (forced)

Current Limit 2/

ICL

VDIF = 15V

1.5

3.5

VDIF = 40V, TA = + 25°C

0.18

1.5

Notes:

1/ Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating

effects are covered under the specification for thermal regulation. With exception of cases U and 2, all output measurements are referenced

to the case. Measurements taken at the output lead must be adjusted for lead resistance.

2/ If not tested, shall be guaranteed to the specified limits.

Negative Regulator

Electrical Performance Characteristics

(TA = -55°C to +125°C, IL = 8mA, Unless otherwise specified)

Parameter

Sym

Conditions

Min

Max

Units

Reference Voltage

VREF

VDIF = 3.0V, TA = + 25°C

-1.275

-1.225

VDIF = 3.0V

-1.3

-1.2

VDIF = 40V, TA = + 25°C

-1.275

-1.225

VDIF = 40V

-1.3

-1.2

Line Regulation

RLINE

3.0V < VDIF < 40V, VOUT = VREF, TA = + 25°C

±9

3.0V < VDIF < 40V, VOUT = VREF

±23

Load Regulation 1/

RLOAD

VDIF = 12V, 8mA < IL < 1.5A, TA = + 25°C

±25

VDIF = 5V, 8mA < IL < 1.5A

±25

VDIF = 40V, 8mA < IL < 200mA, TA = + 25°C

±25

VDIF = 40V, 8mA < IL < 100mA

±25

Thermal Regulation

VRTH

VIN = -14.6V, IL = 1.5A, t = 10ms, PD = 20W,

TA = + 25°C

±5

Ripple Rejection

f = 120Hz, CADJ = 10µF, VOUT = VREF 2/

Adjustment Pin Current

IADJ

VDIF = 3.0V

100

µA

VDIF = 40V

100

µA

Adjustment Pin Current

Change

∆IADJ (Line) 3.0V < VDIF < 40V

±5

µA

∆IADJ (Load) VDIF = 5.0V, 8mA < IL < 1.5A

±5

µA

Minimum Load Current

ILMIN

VDIF = 3.0V, VOUT = -1.4 (forced)

VDIF = 10V, VOUT = 1.4 (forced)

VDIF = 40V, VOUT = 1.4 (forced)

Current Limit 2/

ICL

VDIF = 5V

1.5

3.5

VDIF = 40V, TA = + 25°C

0.24

1.2

Notes:

1/ Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating

effects are covered under the specification for thermal regulation. With exception of cases U and 2, all output measurements are referenced

to the case. Measurements taken at the output lead must be adjusted for lead resistance.

2/ If not tested, shall be guaranteed to the specified limits.

Positive Regulator

Electrical Performance Characteristics (con’t)

(TA = -55°C to +125°C, IL = 8mA, Unless otherwise specified)

Parameter

Sym

Conditions

Min

Max

Units

ACT8600 数据表(PDF) 3 Page - Aeroflex Circuit Technology

ACT8600 数据表(HTML) 3 Page - Aeroflex Circuit Technology

Html Pages

1 2 3 4 5

数据表下载

链接网址

ACT8600 数据表(PDF) 3 Page - Aeroflex Circuit Technology

ACT8600 数据表(HTML) 3 Page - Aeroflex Circuit Technology

Html Pages

1 2 3 4 5

数据表 下载

链接网址

数据表下载