ADP124ACPZ-3.3-R7 datasheet(4/20 Pages) AD

4 / 20 page

ADP124/ADP125

Data Sheet

Rev. C | Page 4 of 20

Parameter

Symbol

Test Conditions

Min

Typ

Max

Unit

OUTPUT NOISE

OUT

NOISE

10 Hz to 100 kHz, V

IN = 5.5 V, VOUT = 1.2 V

µV rms

10 Hz to 100 kHz, V

IN = 5.5 V, VOUT = 1.8 V

µV rms

10 Hz to 100 kHz, V

IN = 5.5 V, VOUT = 2.5 V

µV rms

10 Hz to 100 kHz, V

IN = 5.5 V, VOUT = 3.3 V

µV rms

10 Hz to 100 kHz, V

IN = 5.5 V, VOUT = 4.2V

µV rms

POWER SUPPLY REJECTION RATIO

IN = VOUT +1V)

PSRR

10 kHz to 100 kHz, V

OUT = 1.8 V, 2.5 V, 3.3 V

1 The current from the external resistor divider network in the case of adjustable voltage output (as with the ADP125) should be subtracted from the ground current measured.

2 Accuracy when VOUT is connected directly to ADJ. When VOUT voltage is set by external feedback resistors, absolute accuracy in adjust mode depends on the tolerances of

the resistors used.

3 Based on an endpoint calculation using 1 mA and 500 mA loads.

4 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output voltages

greater than 2.3 V.

5 Start-up time is defined as the time between the rising edge of EN to VOUT being at 90% of its nominal value.

6 Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.3 V

output voltage is defined as the current that causes the output voltage to drop to 90% of 3.3 V, or 2.97 V.

RECOMMENDED CAPACITOR SPECIFICATIONS

Table 2.

Parameter

Symbol

Test Conditions

Min

Typ

Max

Unit

Minimum Input and Output

Capacitance1

CAP

MIN

A = −40°C to +125°C

0.70

µF

Capacitor ESR

ESR

A = −40°C to +125°C

0.001

1 The minimum input and output capacitance should be greater than 0.70 µF over the full range of operating conditions. The full range of operating conditions in the

application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended;

Y5V and Z5U capacitors are not recommended for use with this LDO.

ADP124ACPZ-3.3-R7 数据表(PDF) 4 Page - Analog Devices

ADP124ACPZ-3.3-R7 数据表(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表下载

链接网址

ADP124ACPZ-3.3-R7 数据表(PDF) 4 Page - Analog Devices

ADP124ACPZ-3.3-R7 数据表(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

数据表 下载

链接网址

数据表下载