AD7911AUJZ-R2 datasheet(22/28 Pages) AD

22 / 28 page

AD7911/AD7921

Rev. A | Page 22 of 28

MICROPROCESSOR INTERFACING

The serial interface on the AD7911/AD7921 allows the parts to

be directly connected to a range of microprocessors. This

section explains how to interface the AD7911/AD7921 with

some of the more common microcontroller and DSP serial

interface protocols.

AD7911/AD7921 to TMS320C541 Interface

The serial interface on the TMS320C541 uses a continuous

serial clock and frame synchronization signals to synchronize

the data transfer operations with peripheral devices like the

AD7911/AD7921. The CS input allows easy interfacing between

the TMS320C541 and the AD7911/AD7921 without any glue

logic required. The serial port of the TMS320C541 is set up to

operate in burst mode (FSM = 1 in the serial port control

the SPC register) and the internal frame signal (TXM = 1 in the

SPC register); therefore, both pins are configured as outputs.

For the AD7921, the word length should be set to 16 bits (FO =

0 in the SPC register). This DSP allows frames with a word

length of 16 bits or 8 bits only. In the AD7911, therefore, where

14 bits are required, the FO bit should be set up to 16 bits, and

16 SCLKs are needed. For the AD7911, two trailing zeros are

clocked out in the last two clock cycles.

The values in the SPC register are as follows:

FO = 0

FSM = 1

MCM = 1

TXM = 1

To implement the power-down mode on the AD7911/AD7921,

the format bit, FO, can be set to 1, which sets the word length to

8 bits.

The connection diagram is shown in Figure 32. Note that, for

signal processing applications, the frame synchronization signal

from the TMS320C541 must provide equidistant sampling.

AD7911/

AD7921*

TMS320C541*

CLKX

FSX

FSR

SCLK

DOUT

CLKR

DIN

*ADDITIONAL PINS OMITTED FOR CLARITY

Figure 32. Interfacing to the TMS320C541

AD7911/AD7921 to ADSP-218x

The ADSP-218x family of DSPs are interfaced directly to the

AD7911/AD7921 without any glue logic required. The SPORT

control register should be set up as follows:

TFSW = RFSW = 1, alternate framing

INVRFS = INVTFS = 1, active low frame signal

DTYPE = 00, right-justify data

ISCLK = 1, internal serial clock

TFSR = RFSR = 1, frame every word

IRFS = 0, set up RFS as an input

ITFS = 1, set up TFS as an output

SLEN = 1111, 16 bits for the AD7921

SLEN = 1101, 14 bits for the AD7911

To implement the power-down mode, SLEN should be set to

0111 to issue an 8-bit SCLK burst. The connection diagram is

shown in Figure 33. The ADSP-218x has the TFS and RFS of the

SPORT tied together, with TFS set as an output and RFS set as

an input. The DSP operates in alternate framing mode and the

SPORT control register is set up as described previously. The

frame synchronization signal generated on the TFS is tied to CS

and, as with all signal processing applications, equidistant

sampling is necessary. However, in this example, the timer

interrupt is used to control the sampling rate of the ADC and,

under certain conditions, equidistant sampling might not be

achieved.

AD7911/

AD7921*

ADSP-218x*

SCLK

RFS

TFS

SCLK

DOUT

DIN

*ADDITIONAL PINS OMITTED FOR CLARITY

Figure 33. Interfacing to the ADSP-218x

The timer registers are loaded with a value that provides an

interrupt at the required sample interval. When an interrupt is

received, a value is transmitted with TFS/DT (ADC control

word). The TFS is used to control the RFS and, therefore, the

reading of data. The frequency of the serial clock is set in the

SCLKDIV register. When the instruction to transmit with TFS

is given, that is, TX0 = AX0, the state of the SCLK is checked.

The DSP waits until the SCLK has gone high, low, and high

again before transmission starts. If the timer and SCLK values

are chosen such that the instruction to transmit occurs on or

near the rising edge of SCLK, the data might be transmitted, or

it might wait until the next clock edge.

AD7911AUJZ-R2 数据表(PDF) 22 Page - Analog Devices

AD7911AUJZ-R2 数据表(HTML) 22 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载

链接网址

AD7911AUJZ-R2 数据表(PDF) 22 Page - Analog Devices

AD7911AUJZ-R2 数据表(HTML) 22 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表 下载

链接网址

数据表下载