MPC8245EC datasheet(21/68 Pages) FREESCALE

21 / 68 page

MPC8245 Integrated Processor Hardware Specifications, Rev. 10

Freescale Semiconductor

Electrical and Thermal Characteristics

Table 10. Input AC Timing Specifications

Num

Characteristic

Min

Max

Unit

Notes

10a

PCI input signals valid to PCI_SYNC_IN (input setup)

3.0

—

1, 3

10b

Memory input signals valid to sys_logic_clk (input setup)

10b0

Tap 0, register offset <0x77>, bits 5–4 = 0b00

2.6

—

2, 3, 6

10b1

Tap 1, register offset <0x77>, bits 5–4 = 0b01

1.9

—

10b2

Tap 2, register offset <0x77>, bits 5–4 = 0b10 (default)

1.2

—

10b3

Tap 3, register offset <0x77>, bits 5–4 = 0b11

0.5

—

10c

PIC, misc. debug input signals valid to sys_logic_clk

(input setup)

3.0

—

2, 3

10d

I2C input signals valid to sys_logic_clk (input setup)

3.0

—

2, 3

10e

Mode select inputs valid to HRST_CPU/HRST_CTRL (input setup)

× tCLK

—

2, 3–5

Tos—SDRAM_SYNC_IN to sys_logic_clk offset time

0.4

1.0

11a

sys_logic_clk to memory signal inputs invalid (input hold)

11a0

Tap 0, register offset <0x77>, bits 5–4 = 0b00

—

2, 3, 6

11a1

Tap 1, register offset <0x77>, bits 5–4 = 0b01

0.7

—

11a2

Tap 2, register offset <0x77>, bits 5–4 = 0b10 (default)

1.4

—

11a3

Tap 3, register offset <0x77>, bits 5–4 = 0b11

2.1

—

11b

HRST_CPU/HRST_CTRL to mode select inputs invalid (input hold)

—

2, 3, 5

11c

PCI_SYNC_IN to Inputs invalid (input hold)

1.0

—

1, 2, 3

Notes:

1. All PCI signals are measured from OVDD/2 of the rising edge of PCI_SYNC_IN to 0.4 × OVDD of the signal in question for

3.3-V PCI signaling levels. See Figure 12.

2. All memory and related interface input signal specifications are measured from the TTL level (0.8 or 2.0 V) of the signal in

question to the VM = 1.4 V of the rising edge of the memory bus clock, sys_logic_clk. sys_logic_clk is the same as

PCI_SYNC_IN in 1:1 mode but is twice the frequency in 2:1 mode (processor/memory bus clock rising edges occur on every

rising and falling edge of PCI_SYNC_IN). See Figure 11.

3. Input timings are measured at the pin.

4. tCLK is the time of one SDRAM_SYNC_IN clock cycle.

5. All mode select input signals specifications are measured from the TTL level (0.8 or 2.0 V) of the signal in question to the

VM = 1.4 V of the rising edge of the HRST_CPU/HRST_CTRL signal. See Figure 13.

6. The memory interface input setup and hold times are programmable to four possible combinations by programming bits 5–4

of register offset <0x77> to select the desired input setup and hold times.

7. Tos represents a timing adjustment for SDRAM_SYNC_IN with respect to sys_logic_clk. Due to the internal delay present

on the SDRAM_SYNC_IN signal with respect to the sys_logic_clk inputs to the DLL, the resulting SDRAM clocks become

offset by the delay amount. To maintain phase-alignment of the memory clocks with respect to sys_logic_clk, the feedback

trace length of SDRAM_SYNC_OUT to SDRAM_SYNC_IN must be shortened to accommodate this range. The feedback

trace length is relative to the SDRAM clock output trace lengths. We recommend that the length of SDRAM_SYNC_OUT to

SDRAM_SYNC_IN be shortened by 0.7 ns because that is the midpoint of the range of Tos and allows the impact from the

range of Tos to be reduced. Additional analyses of trace lengths and SDRAM loading must be performed to optimize timing.

For details on trace measurements and the problem of Tos, refer to the Freescale application note AN2164,

MPC8245/MPC8241 Memory Clock Design Guidelines.

MPC8245EC 数据表(PDF) 21 Page - Freescale Semiconductor, Inc

MPC8245EC 数据表(HTML) 21 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

数据表下载