Wideband 2.5 GHz, 37 dB Isolation at 1 GHz,

CMOS 1.65 V to 2.75 V, 4:1 Mux/SP4T

Data Sheet

ADG904/ADG904-R

Rev. C

Document Feedback

InformationfurnishedbyAnalogDevicesisbelievedtobeaccurateandreliable.However,no

responsibilityisassumedbyAnalogDevicesforitsuse,norforanyinfringementsofpatentsorother

rightsofthirdpartiesthatmayresultfromitsuse.Specificationssubjecttochangewithoutnotice.No

licenseisgrantedbyimplicationorotherwiseunderanypatentorpatentrightsofAnalogDevices.

Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

©2004–2013 Analog Devices, Inc. All rights reserved.

Technical Support

www.analog.com

FEATURES

Wideband switch: –3 dB @ 2.5 GHz

ADG904: absorptive 4:1 mux/SP4T

ADG904-R: reflective 4:1 mux/SP4T

High off isolation (37 dB @ 1 GHz)

Low insertion loss (1.1 dB dc to 1 GHz)

Single 1.65 V to 2.75 V power supply

CMOS/LVTTL control logic

20-lead TSSOP and 4 mm × 4 mm LFCSP packages

Low power consumption (1 μA maximum)

Qualified for automotive applications

APPLICATIONS

Wireless communications

General-purpose RF switching

Dual-band applications

High speed filter selection

Digital transceiver front end switch

IF switching

Tuner modules

Antenna diversity switching

FUNCTIONAL BLOCK DIAGRAMS

ADG904

50



50



50



50



1 OF 4 DECODER

RFC

A0

A1

EN

RF1

RF2

RF3

RF4

ADG904-R

1 OF 4 DECODER

RFC

A0

A1

EN

RF1

RF2

RF3

RF4

Figure 1.

Figure 2.

GENERAL DESCRIPTION

The ADG904 and ADG904-R are wideband analog 4:1

multiplexers that use a CMOS process to provide high isolation

and low insertion loss to 1 GHz. The ADG904 is an

absorptive/matched mux with 50 Ω terminated shunt legs; the

ADG904-R is a reflective mux. These devices are designed such

that the isolation is high over the dc to 1 GHz frequency range.

The ADG904 and ADG904-R switch one of four inputs to a

common output, RFC, as determined by the 3-bit binary

address lines A0, A1, and EN. A Logic 1 on the EN pin disables

the device.

The parts have on-board CMOS control logic, which eliminates

the need for external control circuitry. The control inputs

are both CMOS and LVTTL compatible. The low power

consumption of these devices makes them ideally suited

for wireless applications and general-purpose high

frequency switching.

PRODUCT HIGHLIGHTS

1.

−37 dB off isolation @ 1 GHz

2.

1.1 dB insertion loss @ 1 GHz

3.

20-lead TSSOP/LFCSP packages

FREQUENCY (Hz)

10G

10k

100k

1M

10M

100M

1G

–10

–20

–30

–40

–50

–60

–70

–80

S12

S21

FREQUENCY (Hz)

10G

10k

100k

1M

10M

100M

1G

–0.3

–0.4

–0.5

–0.6

–0.7

–0.8

–0.9

–1.0

–1.1

–1.2

–1.3

–1.4

–1.5

–1.6

–1.7

–1.8

–1.9

–2.0

–2.1

–2.2

–2.3

–2.4

–2.5

–2.6

–2.7

–2.8

–2.9

–3.0

Figure 3. Off Isolation vs. Frequency

Figure 4. Insertion Loss vs. Frequency