DSPIC30F2010 datasheet(74/236 Pages) MICROCHIP

74 / 236 page

dsPIC30F6010A/6015

DS70150C-page 72

10.1

Timer Gate Operation

The 32-bit timer can be placed in the Gated Time

Accumulation mode. This mode allows the internal TCY

to increment the respective timer when the gate input

signal (T2CK pin) is asserted high. Control bit TGATE

(T2CON<6>) must be set to enable this mode. When in

this mode, Timer2 is the originating clock source. The

TGATE setting is ignored for Timer3. The timer must be

enabled (TON = 1) and the timer clock source set to

internal (TCS = 0).

The falling edge of the external signal terminates the

count operation, but does not reset the timer. The user

must reset the timer in order to start counting from zero.

10.2

ADC Event Trigger

When a match occurs between the 32-bit timer (TMR3/

TMR2) and the 32-bit combined period register (PR3/

PR2), a special ADC trigger event signal is generated

by Timer3.

10.3

Timer Prescaler

The input clock (FOSC/4 or external clock) to the timer

has a prescale option of 1:1, 1:8, 1:64, and 1:256

selected by control bits TCKPS<1:0> (T2CON<5:4>

and T3CON<5:4>). For the 32-bit timer operation, the

originating clock source is Timer2. The prescaler oper-

ation for Timer3 is not applicable in this mode. The

prescaler counter is cleared when any of the following

occurs:

• a write to the TMR2/TMR3 register

• clearing either of the TON (T2CON<15> or

T3CON<15>) bits to ‘0’

• device Reset such as POR and BOR

However, if the timer is disabled (TON = 0), then the

Timer2 prescaler cannot be reset, since the prescaler

clock is halted.

TMR2/TMR3 is not cleared when T2CON/T3CON is

written.

10.4

Timer Operation During Sleep

Mode

During CPU Sleep mode, the timer will not operate,

because the internal clocks are disabled.

10.5

Timer Interrupt

The 32-bit timer module can generate an interrupt on

period match, or on the falling edge of the external gate

signal. When the 32-bit timer count matches the

respective 32-bit period register, or the falling edge of

the external “gate” signal is detected, the T3IF bit

(IFS0<7>) is asserted and an interrupt will be gener-

ated if enabled. In this mode, the T3IF interrupt flag is

used as the source of the interrupt. The T3IF bit must

be cleared in software.

Enabling

interrupt

accomplished

via

the

respective Timer Interrupt Enable bit, T3IE (IEC0<7>).

DSPIC30F2010 数据表(PDF) 74 Page - Microchip Technology

DSPIC30F2010 数据表(HTML) 74 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载