TC1017 datasheet(2/22 Pages) MICROCHIP

2 / 22 page

TC1017

DS21813D-page 2

1.0

ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

Input Voltage ....................................................................6.5V

Power Dissipation ......................... Internally Limited (Note 7)

Maximum Voltage On Any Pin ..................VIN + 0.3V to -0.3V

† Notice: Stresses above those listed under "Maximum

Ratings" may cause permanent damage to the device. This is

a stress rating only and functional operation of the device at

those or any other conditions above those indicated in the

operation listings of this specification is not implied. Exposure

to maximum rating conditions for extended periods may affect

device reliability.

PIN FUNCTION TABLE

Name

Function

SHDN

Shutdown control input.

No connect

GND

Ground terminal

VOUT

Regulated voltage output

VIN

Unregulated supply input

ELECTRICAL CHARACTERISTICS

Electrical Specifications: Unless otherwise noted, VIN = VR + 1V, IL = 100 µA, CL = 1.0 µF, SHDN > VIH, TA = +25°C

Boldface type specifications apply for junction temperatures of –40°C to +125°C.

Parameter

Sym

Min

Typ

Max

Units

Test Conditions

Input Operating Voltage

VIN

2.7

—

6.0

Note 1

Maximum Output Current

IOUTMAX

150

——

Output Voltage

VOUT

VR – 2.5%

VR ±0.5%

VR + 2.5%

Note 2

OUT Temperature Coefficient

TCVOUT

—

ppm/°C

Note 3

Line Regulation

|(ΔVOUT/ΔVIN)| / V

—0.04

0.2

%/V

(VR + 1V) < VIN < 6V

Load Regulation (Note 4)

|ΔVOUT| / VR

—0.38

1.5

%IL = 0.1 mA to IOUTMAX

Dropout Voltage (Note 5)

VIN – VOUT

—

180

285

—

200

350

500

IL = 100 µA

IL = 50 mA

IL = 100 mA

IL = 150 mA

Supply Current

IIN

—53

µA

SHDN = VIH, IL = 0

Shutdown Supply Current

IINSD

—

0.05

µA

SHDN = 0V

Power Supply Rejection Ratio

PSRR

—

f =1 kHz, IL = 50 mA

Wake-Up Time

(from Shutdown Mode)

tWK

—10

—

µs

VIN = 5V, IL = 60 mA,

CIN = COUT =1 µF,

f = 100 Hz

Note

The minimum V

IN has to meet two conditions: VIN ≥ 2.7V and VIN ≥ (VR + 2.5%) + VDROPOUT.

R is the regulator voltage setting. For example: VR = 1.8V, 2.7V, 2.8V, 3.0V.

Regulation is measured at a constant junction temperature using low duty-cycle pulse testing. Load regulation is tested

over a load range from 0.1 mA to the maximum specified output current. Changes in output voltage due to heating

effects are covered by the thermal regulation specification.

Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal

value at a 1V differential.

Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,

excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for t = 10 msec.

The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction

temperature and the thermal resistance from junction-to-air (i.e., T

A, TJ, θJA). Exceeding the maximum allowable power

dissipation causes the device to initiate thermal shutdown. Please see Section 5.1 “Thermal Shutdown”, for more

details

Output current is limited to 120 mA (typ) when V

OUT is less than 0.5V due to a load fault or short-circuit condition.

TCV

OUT

OUTMAX

OUTMIN

–

() 10

OUT

--------------------------------------------------------------------------------------

TC1017 数据表(PDF) 2 Page - Microchip Technology

TC1017 数据表(HTML) 2 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

数据表下载