| 数据搜索系统,热门电子元器件搜索 |
|
SAP5SD-A-G1-R 数据表(PDF) 39 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
SAP5SD-A-G1-R 数据表(HTML) 39 Page - List of Unclassifed Manufacturers |
|
39 / 63 page ![]() SAP5S / SAP51 Universal Actuator-Sensor Interface IC Data Sheet July 17, 2012 © 2012 Zentrum Mikroelektronik Dresden AG — Rev. 3.1 All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. The information furnished in this publication is PRELIMINARY and subject to changes without notice. 39 of 62 4.9. Data and Parameter Port Configuration Data and Parameter ports are configured by programming the IO_Code in the E²PROM. Moreover, the configuration also depends on the Safety_Mode_Enable settings. NOTE: Below Table 25 refers to slaves not running in Safety Mode (refer to chapter 4.18) The following configurations are possible: OUT: output only, data are valid up to the next DSTBn/PSTBn strobe pulse IN: input only, open drain output is fixed at high-impedance state I/O: bi-directional port with timing according to Figure 6 and Figure 7 INOUT: In case IO_Code = 7 Parameter ports are configured outputs after WPAR master calls and inputs after DEXG master calls, respectively. PASSIV: no input function and open drain output is fixed at high-impedance state If one of the data ports D0…D3 is configured as OUT, the SAP5 slave answer to a DEXG master request contains the respective information bit I0...I3 received from the master. However, parameter ports P0...P3 are always operated bi-directional, including a read-back of the actual port level as described in chapter 4.8 on page 33. Table 25: Data and Parameter Port Configuration for Non-Safety-Mode Operation IO_Code D0 D1 D2 D3 1 P0 P1 P2 P3 1 0 IN IN IN IN OUT OUT OUT OUT 1 IN IN IN OUT OUT OUT OUT OUT 2 IN IN IN I/O OUT OUT OUT OUT 3 IN IN OUT OUT OUT OUT OUT OUT 4 IN IN I/O I/O OUT OUT OUT OUT 5 IN OUT OUT OUT OUT OUT OUT OUT 6 IN I/O I/O I/O OUT OUT OUT OUT 7 2 OUT OUT OUT OUT INOUT INOUT INOUT INOUT 8 OUT OUT OUT OUT OUT OUT OUT OUT 9 OUT OUT OUT IN OUT OUT OUT OUT A OUT OUT OUT I/O OUT OUT OUT OUT B OUT OUT IN IN OUT OUT OUT OUT C OUT OUT I/O I/O OUT OUT OUT OUT D OUT IN IN IN OUT OUT OUT OUT E OUT I/O I/O I/O OUT OUT OUT OUT F 3 PASSIV PASSIV PASSIV PASSIV OUT OUT OUT OUT 1 Slaves running in Extended_Address_Mode (ID_Code = 0xA) will output the respective select bit (I3) at the P3 pin and at the D3 pin in case it is configured as OUT or I/O. 2 The special case IO_Code = 0x7 causes the Parameter Ports acting as Data Inputs after DEXG master calls. Thus a bi-directional data exchange with separate data inputs and outputs is possible. Parameter Ports are always outputs after WPAR master calls. NOTE: IO_Code = 0x7 is not allowed for the SAP5 16 Pin version. 3 There is no data exchange possible in case IO_Code = 0xF, i.e. Data Outputs are always at high impedance state, no slave answer is generated for received DEXG master calls. |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |