80960KB datasheet(14/44 Pages) INTEL

14 / 44 page

80960KB

Table 4. 80960KB Pin Description: L-Bus Signals (Sheet 1 of 2)

NAME

TYPE

DESCRIPTION

CLK2

SYSTEM CLOCK provides the fundamental timing for 80960KB systems. It is

divided by two inside the 80960KB and four 80-bit registers (FP0 through FP3) to

generate the internal processor clock.

LAD31:0

I/O

T.S.

LOCAL ADDRESS / DATA BUS carries 32-bit physical addresses and data to

and from memory. During an address (Ta) cycle, bits 2-31 contain a physical word

address (bits 0-1 indicate SIZE; see below). During a data (Td) cycle, bits 0-31

contain read or write data. These pins float to a high impedance state when not

active.

Bits 0-1 comprise SIZE during a Ta cycle. SIZE specifies burst transfer size in

words.

LAD1

LAD0

1 Word

2 Words

3 Words

4 Words

ALE

T.S.

ADDRESS LATCH ENABLE indicates the transfer of a physical address. ALE is

asserted during a Ta cycle and deasserted before the beginning of the Td state. It

is active LOW and floats to a high impedance state during a hold cycle (Th).

ADS

O.D.

ADDRESS/DATA STATUS indicates an address state. ADS is asserted every Ta

state and deasserted during the following Td state. For a burst transaction, ADS is

asserted again every Td state where READY was asserted in the previous cycle.

W/R

O.D.

WRITE/READ specifies, during a Ta cycle, whether the operation is a write or

read. It is latched on-chip and remains valid during Td cycles.

DT/R

O.D.

DATA TRANSMIT / RECEIVE indicates the direction of data transfer to and from

the L-Bus. It is low during Ta and Td cycles for a read or interrupt acknowl-

edgment; it is high during Ta and Td cycles for a write. DT/R never changes state

when DEN is asserted.

DEN

O.D.

DATA ENABLE (active low) enables data transceivers. The processor asserts

DEN# during all Td and Tw states. The DEN# line is an open drain-output of the

80960KB-processor.

READY

READY indicates that data on LAD lines can be sampled or removed. If READY

is not asserted during a Td cycle, the Td cycle is extended to the next cycle by

inserting a wait state (Tw) and ADS is not asserted in the next cycle.

LOCK

I/O

O.D.

BUS LOCK prevents bus masters from gaining control of the L-Bus during

Read/Modify/Write (RMW) cycles. The processor or any bus agent may assert

LOCK.

At the start of a RMW operation, the processor examines the LOCK pin. If the pin

is already asserted, the processor waits until it is not asserted. If the pin is not

asserted, the processor asserts LOCK during the Ta cycle of the read transaction.

The processor deasserts LOCK in the Ta cycle of the write transaction. During the

time LOCK is asserted, a bus agent can perform a normal read or write but not a

RMW operation.

The processor also asserts LOCK during interrupt-acknowledge transactions.

Do not leave LOCK unconnected. It must be pulled high for the processor to

function properly.

I/O = Input/Output, O = Output, I = Input, O.D. = Open Drain, T.S. = Three-state

ERRATA - 6/13/97

DEN pin description omitted.

80960KB 数据表(PDF) 14 Page - Intel Corporation

80960KB 数据表(HTML) 14 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表下载

链接网址

80960KB 数据表(PDF) 14 Page - Intel Corporation

80960KB 数据表(HTML) 14 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

数据表 下载

链接网址

数据表下载