TSL1401CS datasheet(4/19 Pages) AMSCO

4 / 19 page

TSL1401CS−LF

128 × 1 LINEAR SENSOR ARRAY WITH HOLD

TAOS072E − APRIL 2007

The LUMENOLOGY r Company

www.taosinc.com

Available Options

DEVICE

PACKAGE − LEADS

PACKAGE DESIGNATOR ORDERING NUMBER

TSL1401CS−LF

−40°C to 100°C

Solder Bump − Lead Free − 8

TSL1401CS−LF

Absolute Maximum Ratings†

Supply voltage range, VDD

−0.3 V to 6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input voltage range, VI

−0.3 V to VDD + 0.3V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input clamp current, IIK (VI < 0) or (VI > VDD)

−20 mA to 20 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output clamp current, IOK (VO < 0 or VO > VDD)

−25 mA to 25 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voltage range applied to any output in the high impedance or power-off state, VO

−0.3 V to VDD + 0.3 V

. . .

Continuous output current, IO (VO = 0 to VDD)

−25 mA to 25 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous current through VDD or GND

−40 mA to 40 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Analog output current range, IO

−25 mA to 25 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum light exposure at 638 nm

5 mJ/cm2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating free-air temperature range, TA

−40°C to 100°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Storage temperature range, Tstg

−40°C to 100°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Solder reflow temperature, case exposed for 10 seconds

260°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

Recommended Operating Conditions (see Figure 1 and Figure 2)

MIN

NOM

MAX

UNIT

Supply voltage, VDD

5.5

Input voltage, VI

VDD

High-level input voltage, VIH

VDD

Low-level input voltage, VIL

0.8

Wavelength of light source, λ

400

1000

Clock frequency, fclock

8000

kHz

Sensor integration time, tint (see Note 1)

0.03375

100

Setup time, serial input, tsu(SI)

Hold time, serial input, th(SI) (see Note 2)

Operating free-air temperature, TA

−40

°C

NOTES: 1. Integration time is calculated as follows:

tint (min) = (128 − 18)

y clock period + 20 ms

where 128 is the number of pixels in series, 18 is the required logic setup clocks, and 20 ms is the pixel charge transfer time (tqt)

2. SI must go low before the rising edge of the next clock pulse.

TSL1401CS 数据表(PDF) 4 Page - ams AG

TSL1401CS 数据表(HTML) 4 Page - ams AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

数据表下载

链接网址

TSL1401CS 数据表(PDF) 4 Page - ams AG

TSL1401CS 数据表(HTML) 4 Page - ams AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19

数据表 下载

链接网址

数据表下载