HT48CA3 datasheet(13/36 Pages) HOLTEK

13 / 36 page

HT48CA3

Rev. 1.40

July 16, 2003

T M 1

T M 0

T M R 0

T E

T M 1

T M 0

T O N

P u l s e W i d t h

M e a s u r e m e n t

M o d e C o n t r o l

T i m e r / E v e n t C o u n t e r 0

P r e l o a d R e g i s t e r

8 - b i t

T i m e r / E v e n t C o u n t e r

( T M R 0 )

D a t a B u s

R e l o a d

P F D

8 - s t a g e P r e s c a l e r

8 - 1 M U X

f S Y S

f I N T

P S C 2 ~ P S C 0

( 1 / 2 ~ 1 / 2 5 6 )

¸ 2

O v e r f l o w t o I n t e r r u p t

Timer/Event Counter 0

There are 3 registers related to Timer/Event Counter 1;

TMR1H(0FH), TMR1L(10H), TMR1C(11H). Writing

TMR1L will only put the written data to an internal

lower-order byte buffer (8 bits) and writing TMR1H will

transfer the specified data and the contents of the

lower-order byte buffer to TMR1H and TMR1L preload

registers, respectively. The Timer/Event Counter 1

preload register is changed by each writing TMR1H op-

erations. Reading TMR1H will latch the contents of

TMR1H and TMR1L counters to the destination and the

lower-order byte buffer, respectively. Reading the

TMR1L will read the contents of the lower-order byte

buffer. The TMR1C is the Timer/Event Counter 1 control

able or disable and active edge.

The TM0, TM1 bits define the operating mode. The

event count mode is used to count external events,

which means the clock source comes from an external

(TMR1) pin. The timer mode functions as a normal timer

with the clock source coming from the instruction clock.

The pulse width measurement mode can be used to

count the high or low level duration of the external signal

(TMR1). The counting is based on the instruction clock.

In the event count or timer mode, once the Timer/Event

Counter 1 starts counting, it will count from the current

contents in the Timer/Event Counter 1 to FFFFH. Once

overflow occurs, the counter is reloaded from the

Timer/Event Counter 1 preload register and generates

the corresponding interrupt request flag (T1F;bit 6 of

INTC) at the same time.

In pulse width measurement mode with the TON and TE

bits are equal to one, once the TMR1 has received a

transition from low to high (or high to low if the TE bit is 0)

it will start counting until the TMR1 returns to the original

level and reset the TON. The measured result will re-

main in the Timer/Event Counter 1 even if the activated

transition occurs again. In other words, only one cycle

measurement can be done. Until setting the TON, the

cycle measurement will function again as long as it re-

ceives further transition pulse. Note that, in this operat-

ing mode, the Timer/Event Counter 1 starts counting not

according to the logic level but according to the transi-

tion edges. In the case of counter overflows, the counter

1 is reloaded from the Timer/Event Counter 1 preload

other two modes.

To enable the counting operation, the timer ON bit (TON;

bit 4 of TMR1C) should be set to 1. In the pulse width

measurement mode, the TON will be cleared automati-

cally after the measurement cycle is complete. But in the

other two modes the TON can only be reset by instruc-

tions. The overflow of the Timer/Event Counter 1 is one

of the wake-up sources. No matter what the operation

mode is, writinga0to ET1I can disabled the corre-

sponding interrupt service.

In the case of Timer/Event Counter 1 OFF condition,

writing data to the Timer/Event Counter 1 preload regis-

ter will also load the data to Timer/Event Counter 1. But

if the Timer/Event Counter 1 is turned on, data written to

the Timer/Event Counter 1 will only be kept in the

T M 1

T M 0

T M R 1

T E

T M 1

T M 0

T O N

P u l s e W i d t h

M e a s u r e m e n t

M o d e C o n t r o l

1 6 - b i t

T i m e r / E v e n t C o u n t e r

P r e l o a d R e g i s t e r

D a t a B u s

R e l o a d

O v e r f l o w

t o I n t e r r u p t

1 6 - b i t

T i m e r / E v e n t C o u n t e r

( T M R 1 H / T M R 1 L )

L o w B y t e

B u f f e r

f S Y S / 4

Timer/Event Counter 1

HT48CA3 数据表(PDF) 13 Page - Holtek Semiconductor Inc

HT48CA3 数据表(HTML) 13 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表下载

链接网址

HT48CA3 数据表(PDF) 13 Page - Holtek Semiconductor Inc

HT48CA3 数据表(HTML) 13 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表 下载

链接网址

数据表下载