HSP43124PC-33 datasheet(15/17 Pages) INTERSIL

15 / 17 page

Absolute Maximum Ratings

Thermal Information

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.0V

Input, Output Voltage . . . . . . . . . . . . . . . . . GND -0.5V to VCC +0.5V

ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1

Operating Conditions

Voltage Range (Commercial). . . . . . . . . . . . . . . . . . . 4.75V to 5.25V

Voltage Range (Industrial) . . . . . . . . . . . . . . . . . . . . . 4.75V to 5.25V

Temperature Range (Commercial). . . . . . . . . . . . . . . . . 0oC to 70oC

Temperature Range (Industrial) . . . . . . . . . . . . . . . . . -40oC to 85oC

Thermal Resistance (Typical, Note 1)

θJA (oC/W)

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC

Maximum Storage Temperature . . . . . . . . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC

(SOIC - Lead Tips Only)

Die Characteristics

Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40,304

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe

device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

NOTE:

θJA is measured with the component mounted on an evaluation PC board in free air.

DC Electrical Speciﬁcations

VCC = 5.0V +5%, TA = 0

o to 70oC Commercial, T

A = -40

o to 85oC Industrial

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

MAX

UNITS

Power Supply Current

ICCOP

VCC = Max, FCLK = SCLK = 45MHz

Notes 2, 3

203

Standby Power Supply Current

ICCSB

VCC = Max, Outputs Not Loaded

500

µA

Input Leakage Current

VCC = Max, Input = 0V or VCC

-10

µA

Output Leakage Current

VCC = Max, Input = 0V or VCC

-10

µA

Clock Input High

VIHC

VCC = Max, FCLK and SCLK

3.0

Clock Input Low

VILC

VCC = Min, FCLK and SCLK

0.8

Logical One Input Voltage

VIH

VCC = Max

2.0

Logical Zero Input Voltage

VIL

VCC = Min

0.8

Logical One Output Voltage

VOH

IOH = -5mA, VCC = Min

2.6

Logical Zero Output Voltage

VOL

IOL = 5mA, VCC = Min

0.4

Input Capacitance

CIN

FCLK = SCLK = 1MHz

All Measurements Referenced to GND.

TA = 25

oC, Note 4

-10

Output Capacitance

COUT

-10

NOTES:

2. Power supply current is proportional to frequency. Typical rating is 4.5mA/MHz.

3. Output load per test circuit and CL = 40pF.

4. Not tested, but characterized at initial design and at major process/design changes.

HSP43124

HSP43124PC-33 数据表(PDF) 15 Page - Intersil Corporation

HSP43124PC-33 数据表(HTML) 15 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

数据表下载