数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

AN303 数据表(PDF) 6 Page - STMicroelectronics

部件名 AN303
功能描述  The purpose of this note is to familiarize
PDF  13 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

AN303 数据表(HTML) 6 Page - STMicroelectronics

Back Button AN303 Datasheet HTML 2Page - STMicroelectronics AN303 Datasheet HTML 3Page - STMicroelectronics AN303 Datasheet HTML 4Page - STMicroelectronics AN303 Datasheet HTML 5Page - STMicroelectronics AN303 Datasheet HTML 6Page - STMicroelectronics AN303 Datasheet HTML 7Page - STMicroelectronics AN303 Datasheet HTML 8Page - STMicroelectronics AN303 Datasheet HTML 9Page - STMicroelectronics AN303 Datasheet HTML 10Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 13 page
background image
Latching current – the details
AN303
6/13
Doc ID 3654 Rev 3
Note:
To limit the rate of current rise at turn on (dIT/dt) during the capacitor discharge, the value of
the resistor (R) must be higher than a minimum value (typically 47 ohms for most TRIACs).
A higher dIT/dt than the dI/dt specified in the datasheet may damage the device. The TRIAC
peak current (IT1) is approximately the quotient of the capacitor voltage and the snubber
resistance.
2.2
Latching current measurement
In Figure 7, push button C is used to trigger the TRIAC. The value of the gate current IG is
set to a higher value than the gate current specified in the datasheet (IG = 1.2 x IGT).
Decreasing the resistance R causes the TRIAC current IT to increase. The value of the
latching current IL is the value of the TRIAC current IT when the TRIAC remains on without a
gate current.
Sensitive SCRs, that is, those with a gate triggering current IGT of 200 µA or less, are
measured with a 1 k
Ω resistor connected between gate and cathode.
Figure 7.
Circuit for the measurement of the latching current (IL)
For repeatable results, the TRIAC should be appropriately turned on. The following
guidelines must be applied:
●
The pulse width of the gate current must be at least equal to 1 ms.
●
The applied gate current (IG) must by higher than the specified triggering gate current
(IGT) of the device measured. An IG / IGT ratio higher than or equal to 1.2 is
recommended.
There are four different latching current levels; corresponding to the four triggering
quadrants (refer to Figure 8). These quadrants are defined according to VT polarity (VT is
positive if A2 is set to a higher bias voltage than A1) and gate polarity (IG is positive if it is
sourced to the gate, so it circulates from G to A1):
●
Quadrant I (QI): VT > 0 and IG > 0
●
Quadrant II (QII): VT > 0 and IG < 0
●
Quadrant III (QIII): VT < 0 and IG < 0
●
Quadrant IV (QIV): VT < 0 and IG > 0
IL in QIV is not specified for devices only controlled in the three first quadrants, as
SnubberlessTM, logic level and high temperature TRIACs.
TM: Snubberless is a trademark of STMicroelectronics
IG
IT
A1
A2
G
A
V =
±12V
V =
±12V
C
R2
R1
R1
≥ 33 Ω



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com