X9241AMPIZ datasheet(10/17 Pages) INTERSIL

10 / 17 page

FN8164.7

August 17, 2015

Absolute Maximum Ratings

Thermal Information

Supply Voltage (VCC) Limits

X9241A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ±10%

Max Wiper Current for 2k RTOTAL . . . . . . . . . . . . . . . . . . . . . . ±4mA

Max Wiper Current for 10k and 50k RTOTAL . . . . . . . . . . . . . . ±3mA

Voltage on SCK, SCL or any address

input with respect to VSS . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V

Voltage on any VH/RH, VW/RW or VL/RL

referenced to VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6V/-4V

V = |VH/RH - VL/RL|. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10V

IW (10s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA

Power rating (each pot) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50mW

Temperature under bias. . . . . . . . . . . . . . . . . . . . . . . . -65 to +135°C

Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . -65 to +150°C

Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

Recommended Operating Conditions

Temperature (Commercial) . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C

Temperature (Industrial). . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty.

Analog Specifications

(Over recommended operating conditions unless otherwise stated).

SYMBOL

PARAMETER

TEST CONDITION

LIMITS

UNIT

MIN

(Note 11)

TYP

MAX

(Note 11)

RTOTAL

End to end resistance

-20

+20

Wiper resistance

Wiper Current = (VH - VL)/RTOTAL

130



VTERM

Voltage on any VH/RH, VW/RW or VL/RL Pin

-3.0

Noise

Ref: 1kHz (Note 7)

120

dBV

Resolution

(Note 7)

1.6

Absolute linearity (Note 3)

Rw(n)(actual) - Rw(n)(expected)

±1

MI (Note 5)

Relative linearity (Note 4)

Rw(n + 1) - [Rw(n) + MI]

±0.2

MI (Note 5)

Temperature coefficient of RTOTAL

(Note 7)

±300

ppm/°C

Ratiometric temperature coefficient

(Note 7)

±20

ppm/C

CH/CL/CW Potentiometer capacitances

See Circuit #3 and (Note 7)

15/15/25

lAL

RH, RI, RW leakage current

VIN = VTERM. Device is in stand-by mode.

0.1

µA

DC Electrical Specifications

(Over recommended operating conditions unless otherwise stated.)

SYMBOL

PARAMETER

TEST CONDITION

LIMITS

UNIT

MIN

(Note 11)

TYP

MAX

(Note 11)

lCC

Supply current (active)

fSCL = 100kHz, Write/Read to WCR,

Other Inputs = VSS

3mA

ISB

VCC current (standby)

SCL = SDA = VCC, Addr. = VSS

200

500

µA

ILI

Input leakage current

VIN = VSS to VCC

µA

ILO

Output leakage current

VOUT = VSS to VCC

µA

VIH

Input HIGH voltage

VIL

Input LOW voltage

0.8

VOL

Output LOW voltage

IOL = 3mA

0.4

NOTES:

3. Absolute Linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a

potentiometer.

4. Relative Linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer. It is

a measure of the error in step size.

5. MI = RTOT/63 or (RH – RL)/63, single pot

6. Max = all four arrays cascaded together, Typical = individual array resolutions.

X9241A

X9241AMPIZ 数据表(PDF) 10 Page - Intersil Corporation

X9241AMPIZ 数据表(HTML) 10 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

数据表下载

链接网址

X9241AMPIZ 数据表(PDF) 10 Page - Intersil Corporation

X9241AMPIZ 数据表(HTML) 10 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

数据表 下载

链接网址

数据表下载