ZL6105ALAF datasheet(13/35 Pages) INTERSIL

13 / 35 page

ZL6105

FN6906.5

December 19, 2013

The output voltage can be determined from the R0 (Index0) and

R1 (Index1) values using Equation 4:

Single Resistor Output Voltage Setting Mode

Some applications desire the output voltage to be set using a

single resistor. This can be accomplished using a resistor on the

V1 pin while the V0 pin is tied to SGND. Table 4 lists the available

output voltage settings with a single resistor.

SMBus Mode

The output voltage may be set to any value between 0.6V and

5.0V using a PMBus command over the I2C/SMBus interface.

See Application Note AN2033 for details.

Start-up Procedure

The ZL6105 follows a specific internal start-up procedure after

power is applied to the VDD pin. Table 5 describes the start-up

sequence.

If the device is to be synchronized to an external clock source, the

clock frequency must be stable prior to asserting the EN pin. The

device requires approximately 5ms to 10ms to check for specific

values stored in its internal memory. If the user has stored values

in memory, those values will be loaded. The device will then

check the status of all multi-mode pins and load the values

associated with the pin settings.

Once this process is completed, the device is ready to accept

commands via the I2C/SMBus interface and the device is ready

to be enabled. Once enabled, the device requires a minimum

delay period following an enable signal and prior to ramping its

output, as described in “Soft-Start Delay and Ramp Times” on

page 14. If a soft-start delay period less than the minimum has

been configured (using PMBus commands), the device will

default to the minimum delay period. If a delay period greater

than the minimum is configured, the device will wait for the

configured delay period prior to starting to ramp its output.

After the delay period has expired, the output will begin to ramp

towards its target voltage according to the pre-configured

soft-start ramp time that has been set using the SS pin. It should

be noted that if the EN pin is tied to VDD, the device will still

require approximately 5ms to 10ms before the output can begin

its ramp-up as described in Table 5.

TABLE 4. SINGLE RESISTOR VOUT SETTING

RV1

(kΩ)RV0

VOUT

LOW

0.60

LOW

0.65

12.1

LOW

0.70

13.3

LOW

0.75

14.7

LOW

0.80

16.2

LOW

0.85

17.8

LOW

0.90

19.6

LOW

0.95

21.5

LOW

1.00

23.7

LOW

1.05

26.1

LOW

1.10

28.7

LOW

1.15

31.6

LOW

1.20

34.8

LOW

1.25

38.3

LOW

1.30

42.2

LOW

1.40

46.4

LOW

1.50

51.1

LOW

1.60

56.2

LOW

1.70

61.9

LOW

1.80

68.1

LOW

1.90

LOW

2.00

82.5

LOW

2.10

90.9

LOW

2.20

100

LOW

2.30

110

LOW

2.50

121

LOW

3.00

100

)

(

Index

OUT

(EQ. 4)

133

LOW

3.30

147

LOW

4.00

162

LOW

5.00

178

LOW

5.50

TABLE 4. SINGLE RESISTOR VOUT SETTING (Continued)

RV1

(kΩ)RV0

VOUT

VIN

VOUT

1.33V

21.5 kΩ

16.2 kΩ

FIGURE 9. OUTPUT VOLTAGE RESISTOR SETTING EXAMPLE

ZL6105ALAF 数据表(PDF) 13 Page - Intersil Corporation

ZL6105ALAF 数据表(HTML) 13 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

数据表下载

链接网址

ZL6105ALAF 数据表(PDF) 13 Page - Intersil Corporation

ZL6105ALAF 数据表(HTML) 13 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

数据表 下载

链接网址

数据表下载