HCS410 datasheet(11/36 Pages) MICROCHIP

11 / 36 page

HCS410

Preliminary

DS40158C-page 11

2.3

Code Hopping Mode Special Features

2.3.1

CODE WORD COMPLETION

Code word completion is an automatic feature that

ensures that the entire code word is transmitted, even

if the button is released before the transmission is com-

plete. The HCS410 encoder powers itself up when a

button is pushed and powers itself down after the com-

mand is ﬁnished (Figure 2-7). If MTX3 is set in the con-

ﬁguration word, a minimum of three transmissions will

be transmitted when the HCS410 is activated, even if

the buttons are released.

If less than seven words have been transmitted when

the buttons are released, the HCS410 will complete the

current word. If more than seven words have been

transmitted, and the button is released, the PWM out-

put is immediately switched off.

2.3.2

CODE WORD BLANKING ENABLE

Federal Communications Commission (FCC) part 15

rules specify the limits on fundamental power and

harmonics that can be transmitted. Power is calculated

on the worst case average power transmitted in a

100ms window. It is therefore advantageous to

minimize the duty cycle of the transmitted word. This

can be achieved by minimizing the duty cycle of the

individual bits and by blanking out consecutive words.

Code Word Blanking Enable (CWBE) is used for

reducing the average power of a transmission

(Figure 2-12). Using the CWBE allows the user to

transmit a higher amplitude transmission if the

transmission

length

shorter. The

FCC

puts

constraints on the average power that can be

transmitted by a device, and CWBE effectively prevents

continuous transmission by only allowing the transmis-

sion of every second or fourth word. This reduces the

average power transmitted and hence, assists in FCC

approval of a transmitter device.

The HCS410 will either transmit all code words, 1 in 2

or 1 in 4 code words, depending on the baud rate

selected and the code word blanking option. See

Section 3.7 for additional details.

2.3.3

CRC (CYCLE REDUNDANCY CHECK) BITS

The CRC bits are calculated on the 65 previously trans-

mitted bits. The CRC bits can be used by the receiver

to check the data integrity before processing starts. The

CRC can detect all single bit and 66% of double bit

errors. The CRC is computed as follows:

EQUATION 2-1:

CRC CALCULATION

and

with

and Din the nth transmission bit 0 ≤ n ≤ 64

FIGURE 2-12: CODE WORD BLANKING ENABLE

CRC 1

[]

CRC 0

[]

⊕

CRC 0

[]

CRC 0

[]

⊕

() CRC 1

[]

⊕

CRC 10

[]

One Code Word

CWBE Disabled

(All words transmitted)

CWBE Enabled

(1 out of 2 transmitted)

Amplitude

CWBE Enabled

(1 out of 4 transmitted)

Time

HCS410 数据表(PDF) 11 Page - Microchip Technology

HCS410 数据表(HTML) 11 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表下载

链接网址

HCS410 数据表(PDF) 11 Page - Microchip Technology

HCS410 数据表(HTML) 11 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

数据表 下载

链接网址

数据表下载