TLV2465CPWR datasheet(27/71 Pages) TI1

27 / 71 page

TLV2460, TLV2461, TLV2462, TLV2463, TLV2464, TLV2465, TLV246xA

FAMILY OF LOW POWER RAILTORAIL INPUT/OUTPUT

OPERATIONAL AMPLIFIERS WITH SHUTDOWN

SLOS220J − JULY 1998 − REVISED FEBRUARY 2004

WWW.TI.COM

APPLICATION INFORMATION

shutdown function

Three members of the TLV246x family (TLV2460/3/5) have a shutdown terminal for conserving battery life in

portable applications. When the shutdown terminal is tied low, the supply current is reduced to 0.3

µA/channel,

the amplifier is disabled, and the outputs are placed in a high impedance mode. To enable the amplifier, the

shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left floating, care

should be taken to ensure that parasitic leakage current at the shutdown terminal does not inadvertently place

the operational amplifier into shutdown. The shutdown terminal threshold is always referenced to VDD/2.

Therefore, when operating the device with split supply voltages (e.g.

±2.5 V), the shutdown terminal needs to

be pulled to VDD− (not GND) to disable the operational amplifier.

The amplifier’s output with a shutdown pulse is shown in Figures 22, 23, 24, and 25. The amplifier is powered

with a single 5-V supply and configured as a noninverting configuration with a gain of 5. The amplifier turnon

and turnoff times are measured from the 50% point of the shutdown pulse to the 50% point of the output

waveform. The times for the single, dual, and quad are listed in the data tables.

circuit layout considerations

To achieve the levels of high performance of the TLV246x, follow proper printed-circuit board design techniques.

A general set of guidelines is given in the following.

D Ground planes − It is highly recommended that a ground plane be used on the board to provide all

components with a low inductive ground connection. However, in the areas of the amplifier inputs and

output, the ground plane can be removed to minimize the stray capacitance.

D Proper power supply decoupling − Use a 6.8-µF tantalum capacitor in parallel with a 0.1-µF ceramic

capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers

depending on the application, but a 0.1-

µF ceramic capacitor should always be used on the supply terminal

of every amplifier. In addition, the 0.1-

µF capacitor should be placed as close as possible to the supply

terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less

effective. The designer should strive for distances of less than 0.1 inches between the device power

terminals and the ceramic capacitors.

D Sockets − Sockets can be used but are not recommended. The additional lead inductance in the socket pins

will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board

is the best implementation.

D Short trace runs/compact part placements − Optimum high performance is achieved when stray series

inductance has been minimized. To realize this, the circuit layout should be made as compact as possible,

thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of

the amplifier. Its length should be kept as short as possible. This will help to minimize stray capacitance at

the input of the amplifier.

D Surface-mount passive components − Using surface-mount passive components is recommended for high

performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of

surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small

size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray

inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be

kept as short as possible.

Device TLV2465A is Obsolete

TLV2465CPWR 数据表(PDF) 27 Page - Texas Instruments

TLV2465CPWR 数据表(HTML) 27 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

数据表下载