EMC2113 datasheet(59/88 Pages) MICROCHIP

59 / 88 page

RPM-Based Fan Controller with Multiple Temperature Zones & Hardware Thermal Shutdown

Datasheet

 2013 Microchip Technology Inc.

DS20005251A-page 59

The Fan Configuration 1 Register controls the general operation of the RPM-based Fan Speed Control

Algorithm used on the PWM pin.

Bit 7 - EN_ALGO - enables the RPM-based Fan Speed Control Algorithm. Based on the setting of the

RPM / PWM bit, this bit is automatically set or cleared when the LUT_LOCK bit is set (see Section

7.34, "Look Up Table Configuration Register").



‘0’ - (default) the control circuitry is disabled and the fan driver output is determined by the Fan

Driver Setting Register.



‘1’ - the control circuitry is enabled and the Fan Driver output will be automatically updated to

maintain the programmed fan speed as indicated by the TACH Target Register.

Bits 6- 5 - RANGE[1:0] - Adjusts the range of reported and programmed tachometer reading values.

The RANGE bits determine the weighting of all TACH values (including the Valid TACH Count, TACH

Target, and TACH reading) as shown in Table 7.33, "Range Decode".

Bits 4-3 - EDGES[1:0] - determines the minimum number of edges that must be detected on the TACH

signal to determine a single rotation. A typical fan measured 5 edges (for a 2-pole fan). For more

accurate tachometer measurement, the minimum number of edges measured may be increased.

Increasing the number of edges measured with respect to the number of poles of the fan will cause

the TACH Reading registers to indicate a fan speed that is higher or lower than the actual speed. In

order for the FSC Algorithm to operate correctly, the TACH Target must be updated by the user to

accommodate this shift. The Effective Tach Multiplier shown in Table 7.34, "Minimum Edges for Fan

Rotation" is used as a direct multiplier term that is applied to the Actual RPM to achieve the Reported

RPM. It should only be applied if the number of edges measured does not match the number of edges

expected based on the number of poles of the fan (which is fixed for any given fan).

Contact Microchip for recommended settings when using fans with more or less than 2 poles.

Bit 2-0 - UPDATE - determines the base time between fan driver updates. The Update Time, along

with the Fan Step Register, is used to control the ramp rate of the drive response to provide a cleaner

Table 7.33 Range Decode

RANGE[1:0]

REPORTED MINIMUM

RPM

TACH COUNT

MULTIPLIER

500

1000 (default)

2000

4000

Table 7.34 Minimum Edges for Fan Rotation

EDGES[1:0]

MINIMUM TACH

EDGES

NUMBER OF FAN POLES

EFFECTIVE TACH

MULTIPLIER (BASED ON 2

POLE FANS)

1 pole

0.5

2 poles (default)

3 poles

1.5

4 poles

EMC2113 数据表(PDF) 59 Page - Microchip Technology

EMC2113 数据表(HTML) 59 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88

数据表下载